992G Wheel Loader Machine Systems Caterpillar


Piston Pump (Variable Displacement) - Remove

Usage:

992G 7HR

Removal Procedure

Start By:

  1. Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".

  2. Remove the pilot pump for the implement hydraulic system. Refer to Disassembly and Assembly, "Gear Pump (Implement Pilot) - Remove".

------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


    Note: Put identification marks on all lines, on all hoses and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.



    Illustration 1g00435098


    Illustration 2g00435124

  1. Remove tube assembly (4) from variable displacement pump (1) and from fixed displacement pump (2).

  2. Disconnect tube assembly (5) and hose assembly (3) from hydraulic fitting (6).

  3. Remove hydraulic fitting (6) from fixed displacement pump (2).


    Illustration 3g00435126

  4. Disconnect hose assembly (7), supply hose assembly (8), suction hose assembly (9) and two small hose assemblies (10) from variable displacement pump (1).


    Illustration 4g00435199

  5. Use a hoist and a suitable lifting sling to support variable displacement pump (1).

  6. Remove bolts (11).

  7. Use the hoist to carefully remove variable displacement pump (1). The weight of the variable displacement pump is 138 kg (305 lb).


    Illustration 5g00435258

  8. Remove O-ring seal (12) from the mounting flange of variable displacement pump (1).

Caterpillar Information System:

IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Tilt Cylinder - Remove
966G Wheel Loader and 972G Wheel Loader Power Train Transmission Hydraulic Control
992G Wheel Loader and 854G Wheel Dozer Braking System Service Brake System Pressure - Test
992G Wheel Loader Machine Systems Piston Pump (Fixed Displacement) - Install
966G Wheel Loader and 972G Wheel Loader Power Train Oil Filter (Power Train)
902 and 906 Compact Wheel Loaders Power Train System Hydrostatic System
992G Wheel Loader and 854G Wheel Dozer Braking System Parking Brake Control Cable - Adjust
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Service Brake System Pressure - Test
992G Wheel Loader and 854G Wheel Dozer Braking System Limit Switch (Parking Brake) - Check
623F Wheel Tractor-Scraper Ejector Guide Rollers - Inspect/Lubricate/Replace
992G Wheel Loader and 854G Wheel Dozer Braking System Brake System Air - Purge
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Service Brake Control - Adjust
623F Wheel Tractor-Scraper Ejector Support Rollers - Check/Adjust
966G Wheel Loader and 972G Wheel Loader Power Train Transmission Hydraulic Control Operation
613C Series II Wheel Tractor Power Train Axle Housing - Remove
613C Series II Wheel Tractor Power Train Axle Housing - Install
613C Series II Wheel Tractor Power Train Axle Shaft - Remove
613C Series II Wheel Tractor Power Train Axle Shaft - Install
3512 Industrial Engine Engine Operation with Active Diagnostic Codes
623F Wheel Tractor-Scraper Ejector Support Rollers - Inspect/Pack/Replace
992G Wheel Loader Machine Systems Piston Pump (Variable Displacement) - Install
992G Wheel Loader and 854G Wheel Dozer Braking System Service Brakes - Test
992G Wheel Loader and 854G Wheel Dozer Braking System Parking Brake - Test
D9R Track-Type Tractor Cab Door
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.