Engine Oil Pan - Remove and Install
- 将发动机机油排入合适的容器以便保存或弃置。 请参阅操作和保养手册, "发动机机油 - 更换"。
Show/hide table
图 1 g01048207 - 拆下螺栓 (3)。
- 拆下发动机油底壳 (2) 和密封垫 (1)。
- 如有必要,拆下螺栓 (4),然后从发动机油底壳 (2) 上拆下发动机油底壳 (6) 和密封垫 (5)。
Show/hide table
图 2 g02478074 - 拆下螺栓 (7),然后拆下管组件 (8)。 从管组件上拆下 O 形密封圈。
- 拆下螺栓 (10),然后拆卸滤网组件和管组件 (9)。 从管组件上拆下 O 形密封圈。
- 拆下螺栓、隔板 (11) 和密封垫。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | - | Loctite 蓝色 RTV 有机硅 | - |
B | 1Y-3904 | 粘接剂 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 彻底清洁发动机油底壳、隔板和缸体的配合面。
Show/hide table
图 3 g02478074 Show/hide table图 4 g02479538 Show/hide table图 5 g02478095 - 在缸体、前壳体和飞轮壳体之间的接合处涂抹工具 (A)。
- 将工具 (B) 涂抹到隔板 (11) 的区域 (W)。 将密封垫定位到隔板 (11) 上。
- 将工具 (A) 涂抹到密封垫的区域 (X)。 安装密封垫、隔板 (11) 和螺栓。 在涂抹工具 (A) 后的 10 分钟内安装隔板 (11)。
- 将 O 形密封圈安装在管组件 (9) 上。 用清洁的发动机机油润滑 O 形密封圈,然后将管组件 (9) 安装到发动机机油泵上。 安装螺栓 (10)。
- 将 O 形密封圈安装在管组件 (8) 上。 使用清洁的发动机机油润滑 O 形密封圈,然后将管组件 (8) 安装到发动机机油泵中。 安装螺栓 (7)。
Show/hide table
图 6 g02480276 Show/hide table图 7 g02479658 Show/hide table图 8 g02478139 Show/hide table图 9 g02463392 - 将密封垫 (5) 安装在发动机油底壳 (2) 与发动机油底壳 (6) 之间。 安装螺栓 (4)。 按照数字顺序依次拧紧螺栓 (4)。 按照数字顺序再次依次拧紧螺栓 (4)。 请参阅插图 6。 组装完发动机油底壳后,从发动机油底壳表面上调整多余的密封垫 (5)。
- 将工具 (A) 涂抹到发动机油底壳 (2) 和发动机油底壳 (6) 相接触的接合区域。
- 将工具 (B) 涂抹到发动机油底壳 (2) 的区域 (Y)。 将密封垫 (1) 安装到发动机油底壳 (2) 上。
- 将工具 (A) 涂抹到密封垫 (1) 的区域 (Z)。 安装密封垫 (1)、发动机油底壳 (2) 和螺栓 (3)。 在涂抹工具 (A) 后的 10 分钟内安装发动机油底壳 (2)。
- 根据图 9 中的顺序 (A) 依次拧紧螺栓 (3) 至扭矩为
40 ± 5 N·m (30 ± 4 lb ft) 。 根据图 9 中的顺序 (B) 依次拧紧螺栓 (3) 至扭矩为47 ± 5 N·m (35 ± 4 lb ft) 。 - 向发动机加注发动机机油到正确的油位。 请参阅操作和保养手册, "发动机机油 - 更换"。
注: 安装时应使用新密封垫。 请勿重复使用密封垫。
Caterpillar Information System:
C7 Marine Engine Safety Messages
2005/08/01 Cold Weather Operation Reminder {1000, 1250, 1350, 1355, 1450, 1453, 1456}
2004/03/01 Increase Digital Voltage Regulator life through proper output loading {4467}
C18 Marine Generator Set Engines Engine Speed/Timing Sensor Circuit - Test
Cat Commercial Diesel Engine Fluids Recommendations Conventional Coolant/Antifreeze Cooling System Maintenance
Cat Commercial Diesel Engine Fluids Recommendations Supplemental Coolant Additive
Cat Commercial Diesel Engine Fluids Recommendations General Coolant Information
Cat Commercial Diesel Engine Fluids Recommendations Marine Transmission Oil
C7 Marine Engine Model View Illustrations
C1.5 and C2.2 Marine Generator Set Engines Flywheel - Install
G3300 Engines Safety Messages
C7 Marine Engine Cylinder Head
C15 Petroleum Engines Safety Messages
C-15 Petroleum Engine Flywheel
3126B Petroleum Engine General Hazard Information
3126B Petroleum Engine Fire Prevention and Explosion Prevention
C15 Petroleum Engines Engine Electronics
3126B Petroleum Engine Welding on Engines with Electronic Controls
C-15 Petroleum Engine Engine Description
C7 Marine Engine Engine Oil Filter Base
C7 Marine Engine Reference Material
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Remove
C18 Generator set and C18 Marine Engines Pistons and Connecting Rods - Install
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble