1982/05/03 Caterpillar


Use New 6V4910 Clamp-On Ammeter For Easier Electrical Current Measurement{0651}

Usage:


All Caterpillar Products

Correct electrical current measurements are easier to make with the new 6V4910 AC/DC Clamp-On Ammeter. The advantages of the ammeter are its small size with built in digital display, an internal (inside) power source and lower cost.

Formerly, the ammeter was large and had cable connections. It also needed an outside battery.

The ammeter is simpler to use because you do not have to break the circuit to make a current measurement. It will accept cables up to 19 mm (.75") in diameter.

... The liquid crystal digital display is accurate and easier to read than a meter with a needle.

... Four AA batteries are located inside the handle of the ammeter.

... The ammeter will read current from 1-500 amperes directly on the display. Above this (500-1000 A) correct the number shown according to the chart given in Special Instruction Form Number SEHS8030. Current under 1 ampere and measurements with .1 ampere resolution between .1 and 199 amperes can be measured when you connect the ammeter output to a 6V3030 Digital Multimeter, with a 6V6014 Cable (optional). The current will be read on the multimeter display.


Illustration 1. The 6V4910 Clamp-On Ammeter.

... The jaws of the ammeter open with a lever so the conductor can be inserted. These spring loaded jaws close around the conductor to measure the current.

... A trigger switch will turn the ammeter on. The switch can be locked. When the turn-on trigger is released, you will be able to read the last measurement for five seconds.

... The ammeter can be removed from the wire and the measurement can still be read. This feature is important in limited access areas where the display is hard to see.

... This tool has a zero control for D/C operation. Some of the specifications for the 6V4910 Clamp-On Ammeter are shown in the list that follows.

Complete specifications are included in the Special Instruction SEHS8030.

In addition to the basic ammeter, the following cases and tools are available to protect the tool and for use with it. They must be ordered separately.


Illustration 2. In addition to the Ammeter, these items are also available.

Caterpillar Information System:

1982/05/03 Lubricant Recommendations Changed For All Caterpillar Engines To Combat Effects Of Fuel Sulfur{1318,0375,0374,1280}
1982/05/03 New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03 Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03 6V4960 AC Current Probe Will Measure Current Easier{0652}
1982/04/26 Expansion Tank Changed To Permit Installation Of Water Level Gauge{1354,7470}
1982/04/26 Improved Relief Valve Guide Decreases Maximum Oil Pressure During Cold Weather Starts{1315,1304}
1982/04/19 New Broken Link Spring Used In Governor{1264}
1982/04/19 Improvements Made To 6V3000 Sure Seal Repair Kit{0611,1408}
1982/04/12 Use Correct Size Bolt To Install 5P9736, 6V2156 Or 6V2157 Link Brackets{0644}
1982/04/12 New Seals Improve Pressure Regulator Group{3185,3012}
1982/04/12 Make Sure Hydraulic Pumps Are Installed Correctly{5055,5070,5073}
1982/04/12 Lock Screw For Threaded Crown On Hydraulic Cylinders No Longer Used{5000}
1982/05/03 Use The Correct BrakeSaver Seal Group{1155}
1982/05/03 Use 6V6018 Skiving Vise To Hold XT Hose Assemblies{0623,0626,7554}
1982/05/03 Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/10 Larger Press And Improved Tooling Now Available To Fabricate XT Hose{0623,0624,0664}
1982/05/10 Bolts Now Used Instead Of Studs To Hold Cylinder Heads{1101,1201}
1982/05/10 New Exhaust Tubes And Support Used{1061,1067}
1982/05/10 New Crankshaft Main Bearings Used{1203}
1982/05/10 New Mounting Bracket For Mechanical Shut-Off Cable{7418}
1982/05/10 5P4812 Gauge Group Components Available Separately{0653,1215}
1982/05/10 5P3519 Gauge Group Components Available Separately{0653,1215}
1982/05/10 Be Sure To Use Correct Water Temperature Regulators{1355}
1982/05/10 Fuel Rack Slots Have Improved Wear Resistance{1257}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.