Flywheel - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Lifting Bracket | 2 |
B | FT2712 | Guide Stud | 2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Illustration 1 | g01018440 |
- Raise the temperature of ring gear (3) to a maximum temperature of
300 °C (572 °F) . Install ring gear (3) on flywheel (2).Show/hide tableIllustration 2 g01018439 - Install Tooling (B) in the crankshaft.
- Install Tooling (A) on flywheel (2). Use a suitable lifting device. The weight of the flywheel is approximately
65 kg (143 lb) . Position flywheel (2) on the crankshaft. - Apply clean engine oil to the threads of bolts (1).
- Install bolts (1). Remove Tooling (B). Install bolts (1) in place of Tooling (B).
- Tighten bolts (1) to a torque of
270 ± 40 N·m (200 ± 30 lb ft) . - Remove Tooling (A) from the flywheel.
- Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Note: Ring gear (3) must be installed with the chamfered side of the teeth upward. The chamfered side of the gear teeth will be facing toward the starting motor when the flywheel is installed. This will ensure that the starting motor will engage correctly.
Caterpillar Information System:
C15 On-highway Engine Flywheel - Remove
C15 On-highway Engine Cylinder Head - Remove
3408C, 3412C and 3412D High Performance Marine Engines Connecting Rod
2003/09/01 A New Solenoid Provides Better Starting Conditions {1259}
3126B Industrial Engines CID 0100 FMI 04 Engine Oil Pressure short to ground
C18 Marine Generator Set Engines CID 0041 FMI 04 8 Volt DC Supply short to ground
C18 Marine Generator Set Engines CID 0041 FMI 03 8 Volt DC Supply short to +batt
C13 Engine Fan Drive Mounting Group - Remove and Install
G3406 Engines Governor Linkage - Woodward Hydra-mechanical Governor
G3406 Engines Governor Linkage - PSG Governor
G3406 Engines Governor Linkage - Woodward governor 1724
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Modes Of Operation
C27 and C32 Engines for Caterpillar Built Machines CID 0342 FMI 08 Secondary Engine Speed signal abnormal
C27 and C32 Engines for Caterpillar Built Machines CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C27 and C32 Engines for Caterpillar Built Machines CID 0172 FMI 04 Intake Manifold Air Temp short to ground
C27 and C32 Engines for Caterpillar Built Machines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C27 and C32 Engines for Caterpillar Built Machines CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C27 and C32 Engines for Caterpillar Built Machines CID 0261 FMI 13 Engine Timing Calibration required
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Acronyms
2014/07/30 New Cylinder Head Groups and Valve Mechanisms {1100, 1102, 1121, 1123}
2003/12/01 New Cylinder Head Groups and Valve Mechanisms {1100, 1102, 1121, 1123}
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Related Options
C15 On-highway Engine Alternator - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install