Vibration Damper and Pulley - Remove
Start By:
- Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (9). Remove vibration damper (6).
- Remove bolts (8).
Show/hide table
Illustration 2 g00946319 - Hold a wood block against the inner hub of the crankshaft pulley as shown. Strike the wood block with a hammer in order to loosen the tapered rings.
- Carefully pry the crankshaft pulley away from the crankshaft. The weight of the crankshaft pulley is approximately
10 kg (22 lb) .Note: Do not use a puller tool to remove the crankshaft pulley from the crankshaft.
- Remove thrust block (2) and O-ring seal (1).
- Remove tapered ring (3), tapered ring (4), and spacer (5) from crankshaft pulley (7).
Show/hide table
Illustration 1 | g00946324 |
Caterpillar Information System:
3056E Industrial Engine Vibration Damper and Pulley - Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - Input/Output Cabinet
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - System Cabinet
3054E Industrial Engine Voltage Load Protection Module - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0052-11 Air Inlet Shutoff Shutdown (00)
3056E Industrial Engine Valve Guide - Inspect
3126E Truck Engine Air Inlet and Exhaust System - Inspect
G3606 and G3608 Engines Exhaust Manifold
G3606 and G3608 Engines Exhaust Manifold
3126E Truck Engine Engine Oil Pressure Sensor - Test
C7 On-highway Engine Valve Mechanism Cover
3056E Industrial Engine Air Inlet Heater - Remove and Install
2002/12/23 Washer Pump Assemblies Must Be Primed Properly {7306}
3406E, C-10 and C-12 On-highway Engines 0191-07 Transmission Not Responding (68)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0054-05 Auxiliary Output #06 current low (66)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0054-06 Auxiliary Output #06 current high (66)
C7 and C9 On-Highway Engines 0173-00 High Exhaust Gas Temperature Derate
3056E Industrial Engine Cylinder Head
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0055-05 Auxiliary Output #07 current low (67)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0055-06 Auxiliary Output #07 current high (67)
C1.5 and C2.2 Generator Sets Control Panel
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0246-11 Brake Pedal Switch #1 Fault
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0247-11 Brake Pedal Switch #2 Fault
C7 and C9 On-Highway Engines 0168-01 Low ECM Battery Power (17)