Exhaust Manifold
Show/hide table
Illustration 1 | g00945799 |
(1) Exhaust manifold
(2) Bellows
Use the following procedure to install the exhaust manifolds and the bellows:
- Install the manifolds onto the cylinder heads. Lubricate the bolt threads with 5P-3931 Anti-Seize Compound and hand tighten the bolts.
Note: To avoid damaging the bellows, assemble and disassemble the exhaust manifold segments individually. The bolts and nuts for the bellows may be assembled from either side of the flanges.
- Install the bellows onto the manifolds. Lubricate the threads of the bolts for the bellows with 5P-3931 Anti-Seize Compound. Tighten the bolts for the bellows.
- Tighten the bolts that attach the manifolds to the cylinder heads.
- Tighten the remaining bolts for the bellows.
(3) Adapter
-
Lubricate the adapter's threads with 5P-3931 Anti-Seize Compound .
- Torque ... 200 ± 25 N·m (150 ± 18 lb ft)
(4) Pipe plug
-
Lubricate the plug threads with 5P-3931 Anti-Seize Compound .
- Torque ... 130 ± 20 N·m (95 ± 15 lb ft)
(5) Bolt
Lubricate the bolt threads with 5P-3931 Anti-Seize Compound .
(6) Adapter
-
Lubricate the adapter's threads with 5P-3931 Anti-Seize Compound .
- Torque ... 200 ± 25 N·m (150 ± 18 lb ft)
Caterpillar Information System:
G3606 and G3608 Engines Exhaust Manifold
3126E Truck Engine Engine Oil Pressure Sensor - Test
C7 On-highway Engine Valve Mechanism Cover
3056E Industrial Engine Air Inlet Heater - Remove and Install
3126E Truck Engine Vibration Damper - Check
3126E Truck Engine Basic Engine
G3600 Engines Exhaust Manifold
G3500 Engines Vibration Damper Guard
C4.4 (Mech) Industrial Engine Electric Starting System - Test
3126E Truck Engine Electrical System
2002/12/01 A New Top Piston Ring Promotes Reduced Cylinder Liner Wear {1214, 1215}
3126B Marine Engines Transmission Oil Temperature Sensor Open or Short Circuit - Test
3126E Truck Engine Air Inlet and Exhaust System - Inspect
3056E Industrial Engine Valve Guide - Inspect
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0052-11 Air Inlet Shutoff Shutdown (00)
3054E Industrial Engine Voltage Load Protection Module - Remove and Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - System Cabinet
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - Input/Output Cabinet
3056E Industrial Engine Vibration Damper and Pulley - Install
3056E Industrial Engine Vibration Damper and Pulley - Remove
2002/12/23 Washer Pump Assemblies Must Be Primed Properly {7306}
3406E, C-10 and C-12 On-highway Engines 0191-07 Transmission Not Responding (68)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0054-05 Auxiliary Output #06 current low (66)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0054-06 Auxiliary Output #06 current high (66)