Vibration Damper and Pulley - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 9S-3263 | Thread Lock Compound | - |
- Thoroughly clean the following parts: the bore of the pulley, tapered rings, spacer and nose of the crankshaft.
Note: Do not use a degreaser on the parts.
Show/hide tableIllustration 1 g00946231 - Install spacer (5), the inner tapered ring (4), and the outer tapered ring (3) on crankshaft pulley (7).
Note: The tapered rings must be aligned correctly for proper installation. Do not align the gaps of the tapered rings.
Note: Do not expand the tapered rings.
- Install the key on the crankshaft. Align the crankshaft pulley and the key on the crankshaft. Push the pulley onto the crankshaft.
- Install O-ring seal (1) on thrust block (2). Lubricate the O-ring seal with clean engine oil.
- Lubricate the threads and the shoulder of bolts (8). Position the thrust block and install bolts (8). Tighten the bolts evenly to a final torque of
115 N·m (85 lb ft) . - Position crankshaft vibration damper (6) so that the bolt holes align with pulley (7) and the crankshaft.
- Apply Tooling (A) to the threads of bolts (9) that fasten the vibration damper to the crankshaft. Install bolts (9). Tighten the bolts evenly to a final torque of
78 N·m (58 lb ft) .
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Inspect the vibration damper for leaks and dents. If either condition exists, replace the vibration damper.
End By:
- Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Caterpillar Information System:
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - Input/Output Cabinet
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - System Cabinet
3054E Industrial Engine Voltage Load Protection Module - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0052-11 Air Inlet Shutoff Shutdown (00)
3056E Industrial Engine Valve Guide - Inspect
3126E Truck Engine Air Inlet and Exhaust System - Inspect
G3606 and G3608 Engines Exhaust Manifold
G3606 and G3608 Engines Exhaust Manifold
3126E Truck Engine Engine Oil Pressure Sensor - Test
C7 On-highway Engine Valve Mechanism Cover
3056E Industrial Engine Air Inlet Heater - Remove and Install
3126E Truck Engine Vibration Damper - Check
3056E Industrial Engine Vibration Damper and Pulley - Remove
2002/12/23 Washer Pump Assemblies Must Be Primed Properly {7306}
3406E, C-10 and C-12 On-highway Engines 0191-07 Transmission Not Responding (68)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0054-05 Auxiliary Output #06 current low (66)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0054-06 Auxiliary Output #06 current high (66)
C7 and C9 On-Highway Engines 0173-00 High Exhaust Gas Temperature Derate
3056E Industrial Engine Cylinder Head
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0055-05 Auxiliary Output #07 current low (67)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0055-06 Auxiliary Output #07 current high (67)
C1.5 and C2.2 Generator Sets Control Panel
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0246-11 Brake Pedal Switch #1 Fault
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0247-11 Brake Pedal Switch #2 Fault