Gerotor Motor (Circle Drive) - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
- 安装之前先确保摆线马达的所有部件清洁。 组装过程中,检查马达中使用的所有 O 形密封圈的状况。 如果任何密封圈损坏,则应使用新件进行更换。
- 安装轴承 (18) 。 利用适当的压具将轴承 (18) 压到表面 (X) 下面 7.62 mm (0.300 in) 的深度处。
Show/hide table
图 1 | g00926979 |
Show/hide table
图 2 | g00926505 |
- 安装唇形密封 (17) 。
- 将支承环 (19) 和垫片安装在马达组件上。
Show/hide table
图 3 | g00926506 |
- 将唇形密封 (20) 安装到马达组件上。
- 如果配备,安装滚针轴承 (13) (未显示)。 将滚针轴承压到表面 (Z) 下面 2.92 mm (0.115 in) 的深度处。 将 O 形密封圈 (21) 安装在马达组件上。
- 定位马达组件,使面 (Y) 朝上。 将两个座圈 (15) 和轴承 (14) 安装到轴 (16) 上,如图所示。
Show/hide table
图 4 | g00926242 |
- 将轴 (16) 安装在马达组件上。
- 将连杆 (11) 和轴承 (12) 安装在马达组件上。
Show/hide table
图 5 | g00635545 |
- 将隔套 (10) 和内转子 (9) 安装到马达组件上。
Show/hide table
图 6 | g00992953 |
- 将 O 形密封圈安装在外转子 (7) 中。 将销 (8) 和外转子 (7) 安装到马达组件上。
- 将 O 形密封圈安装到歧管 (6) 的两侧。 将歧管 (6) 安装在马达组件上。
Show/hide table
图 7 | g00635552 |
- 将新环 (5) 安装在内板 (4) 上。
注: 环 (5) 为锥形。 锥面与内板 (4) 的凹槽相啮合。
Show/hide table
图 8 | g00635553 |
- 安装内板 (4) 。 密封圈应朝向外盖。 将外板 (3) 安装到马达组件上。
Show/hide table
图 9 | g00635555 |
- 将盖 (2) 和螺栓 (1) 安装到马达组件上。
注: 关于正确的上紧技术参数,请参阅技术参数, "摆线马达(转盘驱动)"。
Show/hide table
图 10 | g00635556 |
End By: 安装摆线马达。 关于正确的程序,请参阅 拆解和组装, "摆线马达(转盘驱动)- 安装"。
Caterpillar Information System:
3512B Marine Auxiliary Engine Lubrication System Operation - Engine
Do Not Mix the 218-3589 Pistons with any Previously Produced Pistons on 3600 Engines Do Not Mix the 218-3589 Pistons with any Previously Produced Pistons on 3600 Engines
C9 Urban Transit Bus Engine Exhaust Brake Circuit - Test
C9 Urban Transit Bus Engine Engine Temperature Sensor Open or Short Circuit - Test
G3520C and G3520E Engines Alternator Mounting
C9 Urban Transit Bus Engine Exhaust Brake Parameters
G3520C and G3520E Engines Gas Engine Ignition
3512B Marine Auxiliary Engine Engine Will Not Crank
SR4 HV and SR4B HV Generators Bearing - Replace
3512B Marine Auxiliary Engine Turbocharger
C32 Power Module Voltage Regulator Options
C9 Urban Transit Bus Engine Reference Material
120H and 135H Motor Graders Machine Systems Gerotor Motor (Circle Drive) - Disassemble
C7 and C9 On-Highway Engines Injection Actuation Pressure Sensor - Test
3512B Marine Auxiliary Engine Engine Starting
3512B Marine Auxiliary Engine Intermittent Engine Shutdown
C11, C13 and C15 On-highway Engines Sensors and Electrical Connectors
C4.4 (Mech) Industrial Engine Basic Engine
G3520C and G3520E Engines Air Inlet Elbow
C-15, C-16, and C-18 Truck Engines Exhaust Manifold
G3520C and G3520E Engines Junction Box
C-15, C-16, and C-18 Truck Engines Engine Oil Filter Base
TK711, TK721, TK722 and TK732 Track Feller Bunchers Seat Belt - Inspect
C9 Urban Transit Bus Engine Injector Solenoid Circuit - Test