Fuel Transfer Pump - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件名称 | 数量 |
A | 1P-0510 | 冲头套件 | 1 |
注: 检查 O 形密封圈、密封垫和密封件有无磨损或损坏。 如有必要,请更换这些零部件。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 检查支架 (16) 内的轴承 (19)。 如果轴承损坏,则必须更换该支架。 轴承是不可维修部件。
Show/hide table
图 2 g01049858 - 将清洁的发动机机油涂在支架 (16) 的唇形密封件上。 使用工具 (A) 将内唇形密封件 (18) 和外唇形密封件 (17) 安装到支架上。 确保唇形密封件的安装方向正确。
Show/hide table
图 3 g01049863 - 将套筒 (15) 安装到支架 (16) 上。 将 O 形密封圈 (20) 安装到泵壳 (14) 上。 将泵壳套过套筒,放到支架上。
Show/hide table
图 4 g00918557 - 将惰轮 (12) 和传动轴 (13) 装入泵壳 (14) 和支架。
Show/hide table
图 5 g01049868 - 检查泵盘 (9) 中的轴承 (21)。 如果轴承损坏,则必须更换该泵盘。 轴承是不可维修部件。
Show/hide table
图 6 g01049930 - 将 O 形密封圈 (22) 安装到泵盘 (9) 上。 将泵盘放到泵壳的相应位置上。
Show/hide table
图 7 g01049933 - 确保止回阀上的弹簧朝内,然后再将止回阀安装到泵头 (8) 上。 使用工具 (A) 将止回阀安装在泵头内。 安装止回阀,使其与孔内的凸肩接触。
Show/hide table
图 8 g01049937 - 安装泵头 (8) 前,请确保排水孔畅通无阻。 将密封垫 (11) 和泵头 (8) 安装到泵盘的相应位置。 安装螺栓,将燃油输油泵固定在一起。
Show/hide table
图 9 g00918545 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将下列零件装入支架: 菌形阀芯 (3), 阀弹簧 (4), 垫圈 (5) 和 端盖 (6).
Show/hide table
图 10 g00918544 - 将清洁的发动机机油涂在 O 形密封圈 (1) 上。 安装 O 形密封圈。 将传动接头 (2) 安装到传动轴上。
Show/hide table
图 1 | g01049857 |
结束:
- 安装燃油输油泵。 请参考拆卸和组装, "燃油输油泵 - 安装"部分。
Caterpillar Information System:
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Remove
C-15, C-16, and C-18 Engines Electric Starting System - Test
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Air Inlet Manifold - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Drawings of Customer Installed Options
C-10 and C-12 Truck Engines Housing (Front)
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Aftercooler - Remove and Install - Aftercooler Housing with 12 bolts
3054E and 3056E Industrial Engines Turbocharger - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Excessive Engine Oil Consumption - Inspect
G3500B Engines Pistons, Rings and Connecting Rods
G3500B Engines Cylinder Block, Liners and Heads
3054E Industrial Engine Front Housing and Covers
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Turbocharger - Disassemble
3054E Industrial Engine Gear Group (Front)
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Reference Information
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Specific Connection Diagrams
C9 Urban Transit Bus Engine Alternator and Regulator
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Abbreviations
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Basic Connection Diagrams
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Connection Diagrams for Schematic Codes 10XXXX
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Connection Diagrams for Schematic Codes 11XXXX
G3304 and G3306 Engines Turbocharger - Remove
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Connection Diagrams for Schematic Codes 12XXXX