Aftercooler - Remove and Install - Aftercooler Housing with 12 bolts
- 从辅助水冷系统将冷却液排入合适的容器,以便保存或处理。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
Show/hide table
图 1 g02173968 - 拆下管组件 (1) 和管组件 (2)。
Show/hide table
图 2 g02173971 - 拆下管组件 (3) 和软管组件 (4)。
Show/hide table
图 3 g02173972 - 拆下软管卡箍 (6) 和软管 (7)。 拆下螺栓 (9)、弯头 (5) 和 O 形密封圈。 拆下螺栓 (10)、弯头 (8) 和 O 形密封圈。 对其余的涡轮增压器重复同样操作。
Show/hide table
图 4 g02173973 - 拆下螺栓 (14)。 由两名技师拆下盖 (13)。 盖 (13) 的重量约为
32 kg (71 lb) 。 从管 (12) 上滑下盖 (13)。 从后冷器芯拆下 O 形密封圈。 拆下螺栓 (11)、管 (12) 和 O 形密封圈。 对其他盖重复该步骤。Show/hide table图 5 g02173975 - 从弯头 (16) 上断开管组件 (18)。 拆下螺栓 ( 17 )并从弯头 (16) 上断开管组件和法兰。 拆下 O 形密封圈。 拆下螺栓 (15)、弯头 ( 16)、适配器和 O 形密封圈。
Show/hide table
图 6 g02174147 - 从三通 (20) 拆下螺栓 (19),并拆下卡箍组件。 拆下螺栓 ( 22)、法兰 ( 21) 和三通 (20)。 拆下适配器和 O 形密封圈。
Show/hide table
图 7 g02174148 - 拆下螺栓 ( 23)、盖 (24)、垫片、适配器和 O 形密封圈。
Show/hide table
图 8 g02174212 - 由两名技师拆下后冷器芯 (25)。 后冷器芯 (25) 的重量约为
45 kg (100 lb) 。 将 O 形密封圈从壳体拆下。 对另一个后冷器芯重复该步骤。Show/hide table图 9 g02174219 - 拆下螺栓 (27)。 由两名技师拆下壳体 (26)。 壳体 (26) 的重量约为
26 kg (57 lb) 。 从进气歧管拆下 O 形密封圈。 对其他壳体重复该步骤。
- 将后冷器芯放在其侧面,安装密封圈。 确保它完全就位。 用可移除的胶带粘贴侧面,确保密封件在组装期间保持就位。
Show/hide table
图 11 g06050591 - 提升后冷器芯和顶盖时,请使用适当的起吊设备。 如图 11 所示,在对齐螺栓孔的同时,将后冷器芯垂直放下。 安装顶部后冷器密封件,确保其完全就位。 将顶盖垂直向下安装,确保无倾斜。
Show/hide table
图 12 g02174250 注: 零扭矩参考意味着将螺栓安装到最小阻力。
- 在进气歧管上安装 O 形密封圈。 以零扭矩安装螺栓,从中间开始并使用图 12 中所示的模式。 使用图 12 中的模式。 将螺栓拧紧至 50%
24 N·m (18 lb ft) 检查密封件是否有正确就座、是否有气泡或凸起。 完成扭矩至 100%47 N·m (35 lb ft) 并检查是否有气泡或凸起。Show/hide table图 13 g02174212 - 将 O 形密封圈安装在壳体上。 由两名技师安装后冷器芯 (25)。 后冷器芯 (25) 的重量约为
45 kg (100 lb) 。 对另一个后冷器芯重复该步骤。Show/hide table图 14 g02173973 - 将 O 形密封圈安装在后冷器芯上。 由两名技师安装盖 (13)。 盖 (13) 的重量约为
32 kg (71 lb) 。 - 在 O 形密封圈上涂抹一层薄薄的甘油。 在另一个盖上安装 O 形密封圈、管 (12 )和螺栓 (11)。 由两名技师安装另一个盖。 在盖 (13 )中滑动管 ( 12)。 安装螺栓 (14)。 拧紧角部螺栓以安放 O 形密封圈。 随后拧紧其余螺栓。
Show/hide table
图 15 g02174148 - 在 O 形密封圈上涂抹一层薄薄的甘油。 安装 O 形密封圈、适配器、垫片、盖 (24 )和螺栓 ( 23)。 此时不要拧紧螺栓。
Show/hide table
图 16 g02174147 - 在 O 形密封圈上涂抹一层薄薄的甘油。 安装 O 形密封圈、适配器、三通 (20)、法兰 (21 )和螺栓 ( 22)。 安装卡箍组件和螺栓 (19)。 此时不要拧紧螺栓。
Show/hide table
图 17 g02173975 - 在 O 形密封圈上涂抹一层薄薄的甘油。 安装 O 形密封圈、适配器、弯头 ( 16) 和螺栓 (15)。 将管组件和法兰连接至弯头 (16),然后安装螺栓 (17)。 将管组件 (18) 连接到弯头 (16)。 此时不要拧紧螺栓。
Show/hide table
图 18 g02174347 - 按数字顺序将盖的螺栓拧紧至扭矩为
24 N·m (18 lb ft) 。 再次按数字顺序将螺栓拧紧至扭矩为47 N·m (35 lb ft) 。 - 拧紧水弯头的螺栓。
Show/hide table
图 19 g02173972 - 安装 O 形密封圈、弯头 (8) 和螺栓 (10)。 在 O 形密封圈上涂抹一层薄薄的甘油。 安装 O 形密封圈、弯头 (5) 和螺栓 (9)。 安装软管 (7 )和软管卡箍 (6)。 使软管卡箍朝向彼此成 180 度。 对其余的涡轮增压器重复同样操作。
Show/hide table
图 20 g02173971 - 安装软管组件 (4) 和管组件 (3)。
Show/hide table
图 21 g02173968 - 安装管组件 (2) 和管组件 (1)。
- 为辅助水冷系统重新加注冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
Show/hide table
图 10 | g06050585 |
Caterpillar Information System:
3054E and 3056E Industrial Engines Turbocharger - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Excessive Engine Oil Consumption - Inspect
G3500B Engines Pistons, Rings and Connecting Rods
G3500B Engines Cylinder Block, Liners and Heads
Installation Procedure for the 223-6519 Cylinder Head Group or the 223-6521 Cylinder Head Group {1101, 1124} Installation Procedure for the 223-6519 Cylinder Head Group or the 223-6521 Cylinder Head Group {1101, 1124}
G3500B Engines Lubrication System
Installation Procedure for the 206-7748 Cylinder Head Group or the 223-6524 Cylinder Head Group {1124} Installation Procedure for the 206-7748 Cylinder Head Group or the 223-6524 Cylinder Head Group {1124}
G3516B Engines MID 036 - CID 0109 - FMI 03 Coolant Outlet Pressure open/short to +batt
Troubleshooting Compressed Air System Components and Performance{1803, 5500} Troubleshooting Compressed Air System Components and Performance{1803, 5500}
3054 and 3056 Marine Generator Set Engines Air Inlet and Exhaust System
3524B Engine for Caterpillar Built Machines Bearing Clearance - Check
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Transmission Oil Cooler - Remove and Install
C-10 and C-12 Truck Engines Housing (Front)
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Drawings of Customer Installed Options
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Air Inlet Manifold - Remove and Install
C-15, C-16, and C-18 Engines Electric Starting System - Test
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Remove
3524B Engine for Caterpillar Built Machines Fuel Transfer Pump - Assemble
3054E Industrial Engine Front Housing and Covers
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Turbocharger - Disassemble
3054E Industrial Engine Gear Group (Front)
SR4BHV and SR4HV Electric Power Generation Connection Diagram - SR4 HV ; SR4B HV Reference Information