Piston Cooling Jets - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 9S-9082 | Engine Turning Tool | 1 |
Start By:
- Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to rotate the crankshaft in order to access piston cooling jet (1). Remove bolt (2). Remove piston cooling jet (1).
Show/hide table
| |
| Illustration 1 | g01095931 |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 9S-9082 | Engine Turning Tool | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position piston cooling jet (1) on the engine. Install bolt (2). Tighten bolt (2) to a torque of
25 ± 6 N·m (18 ± 4 lb ft) .
Show/hide table
|
| |
| Illustration 2 | g01095931 |
End By:
- Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) Fault Description
3054 and 3056 Marine Generator Set Engines Lubrication System
Electronic Modular Control Panel II (EMCP II) Engine Setpoint Verification OP9
Electronic Modular Control Panel II (EMCP II) Voltmeter/Ammeter Programming OP8
Electronic Modular Control Panel II (EMCP II) Hourmeter Programming OP7
3126B and 3126E Truck Engine Exhaust Particulate Filter Diagnostic Module - Test
3054 and 3056 Industrial and Generator Set Engines Connecting Rod
3412E, C30 and C32 Marine Engines CID 0105 FMI 04 Inlet Manifold Temp Sensor short to ground
3412E, C30 and C32 Marine Engines CID 0105 FMI 03 Inlet Manifold Temp Sensor open/short to +batt
3412E, C30 and C32 Marine Engines Electrical Power Supply Circuit - Test
Electronic Modular Control Panel II (EMCP II) Spare Input/Output Programming OP6
2002/07/01 New Exhaust Manifolds Are Available {1059}
Electronic Modular Control Panel II (EMCP II) Alarm Modules
3126B and 3126E On-highway Engines 0111-03 Coolant Level voltage high (12)
Electronic Modular Control Panel II (EMCP II) Display of Voltage or Current is Inaccurate
2002/05/01 The New 204-8041 Gauge Group Is Available To Measure The Top Ring Groove On Pistons {1214}
Electronic Modular Control Panel II (EMCP II) GSC CID 0268 - FMI 02
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Electrical Connector - Inspect
Electronic Modular Control Panel II (EMCP II) EMCP Electronic Control (AC Transformer Box) - Replace
3412E, C30 and C32 Marine Engines Pistons and Connecting Rods - Remove
Electronic Modular Control Panel II (EMCP II) EMCP Electronic Control (Generator Set) - Replace
3500 Generator Set Engines Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
3412E, C30 and C32 Marine Engines Pistons and Connecting Rods - Install
PMG3516 Power Module Fuel Metering Valve - Check - Raptor