Rocker Shaft and Pushrod - Install
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install pushrods (4) into the cylinder head.
Note: Ensure that the pushrods are installed in the original location and that the pushrods are seated in the valve lifters correctly.
Show/hide table
Illustration 1 | g00572218 |
3056 Engine |
- Install a new oil seal in the oil supply passage in the cylinder head.
- Install rocker shaft assembly (3) .
Note: Ensure that the adjustment screws are seated in the ends of pushrods (4) .
Show/hide table
Illustration 2 | g00572217 |
3056 Engine |
- Lubricate nuts (1) and bolt (2) with clean engine oil.
- Alternately tighten the nuts and the bolt. Begin in the center and work toward the outside. Tighten the nuts and bolt on an aluminum bracket to a torque of 40 N·m (30 lb ft). Tighten the nuts and bolt on a cast iron bracket or a steel bracket to a torque of 75 N·m (55 lb ft).
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Caterpillar Information System:
2002/02/01 New Special Instruction, REHS1178, "Operating Instructions For The 4P-4788 Electrical Converter Gp And The 4P-4789 Electrical Converter Gp" Is Available {1421}
3054, 3054B and 3056 Marine Engines Rocker Shaft and Pushrod - Remove
3512B Engine for SPF343, SPS343, and SPT343 Pumpers CAT Data Link
C7 and C9 On-Highway Engines Powertrain Data Link Circuit - Test
2002/02/01 A New Systems Operation/Testing And Adjusting Module, RENR5889, "Standby Pump Panel" Is Available {0758}
CPT372 Truck Mounted Pumper Control Panel
2002/05/01 New Starting Motors Used {1453}
318C and 319C Excavators Machine System Specifications Track Roller (Single Flange)
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Disassemble
G3612 and G3616 Engines Engine Support - Remove and Install
2002/02/01 Correction To Disassembly and Assembly Module, SENR5535-04, "G3612 and G3616 Engines" , "Cylinder Head - Remove" {1100}
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Track Roller (Single Flange)
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Assemble
Procedure For Sealing Cracks In The Air Plenum That Are On The Top Surface Of The Cylinder Block{1201} Procedure For Sealing Cracks In The Air Plenum That Are On The Top Surface Of The Cylinder Block{1201}
324D and 326D Excavators Machine System Specifications Track Roller Mounting
3408E and 3412E Engines for Caterpillar Built Machines Electric Starting Motor
C12 Marine Engines Electric Starting Motor
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0001 FMI 11 Cylinder #1 Injector fault
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0002 FMI 11 Cylinder #2 Injector fault
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0003 FMI 11 Cylinder #3 Injector fault
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0004 FMI 11 Cylinder #4 Injector fault
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0005 FMI 11 Cylinder #5 Injector fault
2002/02/25 Introduction of a New Tappet Plug {1209}
2002/02/01 Introduction of a New Tappet Plug {1209}