Air Starting Motor
Type 1
Show/hide table
Illustration 1 | g00853131 |
(1) Cover
- Tighten the cover bolts evenly in small increases until the following torque is reached: ... 82 N·m (60 lb ft)
(2) Bolt
- Torque for bolts ... 38 N·m (28 lb ft)
(3) Bolt
- Torque for bolt ... 78 N·m (57 lb ft)
(4) Bolt
- Tighten the bolt that holds the pinion to the following torque. Right hand side mounted starters have a left hand threaded bolt. Left hand side mounted starters have a right hand threaded bolt: ... 109 N·m (80 lb ft)
(5) Rotor clamp nut
- Tighten the rotor clamp nut until the following clearance between the rear end plate and the rotor is reached: ... 0.03 to 0.08 mm (0.001 to 0.003 inch)
Check the clearance again after the bolt for the rotor clamp nut is tightened.
(6) Bolt
- Tighten the bolt that holds the rotor to the following torque: ... 122 N·m (90 lb ft)
Type 2
Show/hide table
Illustration 2 | g00853467 |
(1) Torque for bolts ... 34 N·m (25 lb ft)
(2) Torque for bolts ... 11 N·m (8 lb ft)
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) GSC CID 0269 - FMI 04
Electronic Modular Control Panel II (EMCP II) GSC CID 0269 - FMI 03
Electronic Modular Control Panel II (EMCP II) GSC CID 0268 - FMI 02
Electronic Modular Control Panel II (EMCP II) GSC CID 0248 - FMI 09 (for EUI Engines)
3500 Generator Set Engines Jacket Water Heater
CPT372 Truck Mounted Pumper Specifications
C12 Marine Engine Engine Valve Lash - Inspect/Adjust
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Recoil Spring - Assemble
Electronic Modular Control Panel II (EMCP II) GSC CID 0190 - FMI 03
Electronic Modular Control Panel II (EMCP II) GSC CID 0190 - FMI 02
SR4 Generator with VR3 or VR4 Voltage Regulator Rotor - Remove and Install
SR4 Generator with VR3 or VR4 Voltage Regulator Generator - Align
Electronic Modular Control Panel II (EMCP II) GSC CID 0333 - FMI 03
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Piston Height - Inspect
Electronic Modular Control Panel II (EMCP II) GSC CID 0333 - FMI 04
C12 Marine Engines Engine Rating Definitions
3054 and 3056 Marine Generator Set Engines Heat Exchanger - Disassemble - 3054 Engine
Electronic Modular Control Panel II (EMCP II) GSC CID 0334 - FMI 03 (for EUI Engines)
3054 and 3056 Marine Generator Set Engines Heat Exchanger - Assemble - 3054 Engine
3500 Generator Set Engines Turbocharger
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Track Adjuster - Disassemble
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Track Adjuster - Assemble
Power Module Switchgear (Low Voltage and Medium Voltage) Troubleshooting
C12 Marine Engines Engine Support (Front)