Travel Motor - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
(A)     | 138-7574     | Link Bracket     | 1     |
(B)     |     | 254 mm (10 inch) of M16 X 20 Threaded Rod     | 1     |
- Thoroughly clean the mating surfaces of the travel motor and the final drive.
- Check the condition of the O-ring seal that is used between the travel motor and the final drive. If the O-ring seal is damaged, use a new part for replacement.
- Install the O-ring seal on the body to travel motor (4). Apply clean hydraulic oil on the O-ring seal.
Show/hide table
Illustration 1 | g00484238 |
- Fasten Tooling (A) and a hoist to travel motor (4), as shown. Carefully install the travel motor on Tooling (B). Slide the travel motor into the final drive.
- Install one of the three bolts (3). Remove Tooling (B) and install the remaining two bolts (3) .
- Connect hose assemblies (1) and (2) to the travel motor. Tighten the two hose assemblies to a torque of 80 ± 7 N·m (60 ± 5 lb ft).
Show/hide table
Illustration 2 | g00484237 |
- Fill the final drive with hydraulic oil to the correct level.
Note: Refer to Operation and Maintenance Manual, "Lubricant Viscosities and Refill Capacities" for the correct filling procedure and for the correct levels.
End By: Install the travel brake valve. Refer to Disassembly and Assembly, "Travel Brake Valve - Install" in this section.
Caterpillar Information System:
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzle - Test
C12 Marine Engine Electronic Control System Components
C12 Marine Engine General Information
3126B and 3126E On-highway Engines Fan Drive Mounting Group - Remove and Install
Power Module Switchgear (Low Voltage and Medium Voltage) Electrical Connections - Check
3408E and 3412E Industrial Engines Temperature Sensor (Auxiliary)
3408E and 3412E Industrial Engines Engine Oil Temperature Sensor
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Travel Motor - Assemble
3054 and 3056 Engines 550 Generator Set Control Panel System Information
3126 Truck Engine (Military) Engine Oil Pressure - Test
3126 Truck Engine (Military) Engine Valve Lash - Inspect/Adjust
385B Excavator Swing Gear - Lubricate
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Final Drive - Remove
C12 Marine Engine Air Inlet and Exhaust System
3408E and 3412E Industrial Engines Injection Actuation Pressure Sensor
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Final Drive - Disassemble
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Firmware
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Final Drive - Assemble
3126E and 3126B Commercial and Truck Engines Fuel Inlet Screen - Clean/Inspect/Replace - If Equipped
3054 and 3056 Engines 550 Generator Set Control Panel Indicators
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Final Drive - Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Firmware Compatibility
3408E and 3412E Industrial Engines Maintenance Interval Schedule - 3408E Industrial Engine
3408E and 3412E Industrial Engines Maintenance Interval Schedule - 3412E Industrial Engine