Fault Identification
Show/hide table
Fault Code Description     | ||||
Indicator left side of GSC     |
Fault Code on upper display     | DIAG Indicator     | Fault Type     | Topic     |
Fault Alarm     | CID FMI (1)     | Flashing     | Active Alarm     | Troubleshooting Diagnostic Codes     |
SP1, SP2, SP3, (1) | Missing     | Active Alarm     | Diagnostic Code Procedure, "SP Fault Code"     | |
AL1 through AL4 (1) | Missing     | Active Alarm     | Diagnostic System Procedures, "AL Fault Code"     | |
Fault Shutdown     | CID FMI     | Flashing     | Active Shutdown     | Troubleshooting Diagnostic Codes     |
SP1, SP2, SP3, | Missing     | Active Shutdown     | Diagnostic System Procedures, "SP Fault Code"     | |
Dedicated Shutdown:     |     | |||
Flashing     | Missing     | Missing     | Active Alarm     | Troubleshooting Dedicated Shutdown Indicators     |
On Continuously     | Missing     | Missing     | Active Shutdown     | |
None     | CID FMI (2)     | On Continuously     | Inactive Alarm     | Troubleshooting Diagnostic Codes     |
CID FMI (2) | On Continuously     | Inactive Shutdown     | Troubleshooting Diagnostic Codes     | |
SP1, SP2, SP3, | Missing     | Inactive Shutdown     | Diagnostic System Procedures, "SP Fault Code"     | |
Missing | Missing     | Undiagnosed Shutdown     | Symptom Procedures     |
Show/hide table
( 1 ) | Fault code is shown after the alarm code key is pressed. |
( 2 ) | Fault Code is stored in the fault log of the GSC. To view the fault code, see Systems Operation, "Fault Log Viewing OP1" within the topic Service Mode. |
Show/hide table
Illustration 1 | g00614724 |
GSC Display Area (1) Dedicated shutdown indicators (2) Spare fault indicators (3) Fault shutdown indicator (4) Fault alarm indicator (5) Upper display (6) Lower display (7) Keypad (8) DIAG indicator |
Faults that are detected and diagnosed by the GSC are shown to service personnel in the display area of the GSC. The GSC uses dedicated shutdown indicators (1), fault shutdown indicator (3), fault alarm indicator (4), "DIAG" indicator (8), upper display (5) and lower display (6) to tell service personnel about a fault. Perform the following procedure in order to identify the fault that is detected by the GSC.
Note: The "DIAG" indicator (8) functions when diagnostic information is available from the GSC.
- Make a note of the indicators that are functioning on the left side of the "GSC".
- View the fault code on the upper display (5). If the fault alarm indicator (4) is FLASHING and no fault code is present on the upper display (5), press the alarm codes key in order to view the fault code.
- Make a note of whether or not "DIAG" indicator (8) is FLASHING ON CONTINUOUSLY or MISSING.
- On the fault identification chart, look at the first column. Locate the fault indicator that is functioning.
- Go to the second column in the chart. Find the fault code that is presently shown on the upper display (5) .
- Go to the third column in the chart which describes the status of "DIAG" indicator (8) .
- Read the last two columns in order to find the type of fault and corresponding topic within this module.
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) General Information
3024C Engine for Caterpillar Built Machines Rocker Shaft - Assemble
3024C Engine for Caterpillar Built Machines Rocker Shaft - Disassemble
Machine Security System Product Identification Number - Program
3024C Engine for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
Machine Security System Time - Set
2001/10/01 Commercial Folded Core Radiators Can Be Converted to Multiple Row Module Radiators {1353}
2001/10/01 Improved Troubleshooting Procedures for EMCPII, EMCPII+, and EMCPII+P Annunciators {4490}
Automatic Transfer Switches CTG, CTGD Series Timers
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Nozzles
3054 and 3056 Marine Generator Set Engines Fuel Injection Pump
2001/11/01 A New Rear Housing Assembly is Available {1157}
Electronic Modular Control Panel II (EMCP II) Service Tools
3054 and 3056 Engines 520 Generator Set Control Panel General Information
3054 and 3056 Industrial and Generator Set Engines Cylinder Head Valves
3054 and 3056 Industrial and Generator Set Engines Cylinder Head
Electronic Modular Control Panel II (EMCP II) Troubleshooting Diagnostic Codes
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0334 - FMI 04 (for MUI and PEEC Engines)
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0336 - FMI 02
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0441 - FMI 12 (for EUI Engines)
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Flywheel - Remove
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0441 - FMI 12 (for PEEC Engines)
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0442 - FMI 12