Crankshaft Position for Valve Lash Setting
从飞轮端看曲轴时,SAE 标准发动机曲轴的旋转方向为逆时针方向。
Show/hide table
曲轴的气门间隙设置位置
标准逆时针旋转 |
|||
---|---|---|---|
发动机 | 第 1 缸处于上死点位置时的冲程 (1) | 进气门 | 排气门 |
G3508 | 压缩冲程 | 1-2-6-8 | 1-2-3-7 |
排气冲程 | 3-4-5-7 | 4-5-6-8 | |
点火顺序 | 1-2-7-3-4-5-6-8 | ||
G3512 | 压缩冲程 | 1-3-6-7-10-12 | 1-4-5-6-9-12 |
排气冲程 | 2-4-5-8-9-11 | 2-3-7-8-10-11 | |
点火顺序 | 1-12-9-4-5-8-11-2-3-10-7-6 | ||
G3516 | 压缩冲程 | 1-2-5-7-8-12-13-14 | 1-2-3-4-5-6-8-9 |
排气冲程 | 3-4-6-9-10-11-15-16 | 7-10-11-12-13-14-15-16 | |
点火顺序 | 1-2-5-6-13-14-9-10-15-16-11-12-3-4-7-8 | ||
G3520 | 压缩冲程 | 1-2-5-6-9-10-11-13-14-17-18 | 1-2-3-4-11-12-13-14-15-16 |
排气冲程 | 3-4-7-8-12-15-16-19-20 | 5-6-7-8-9-10-17-18-19-20 | |
点火顺序 | 1-2-11-12-3-4-15-16-7-8-19-20-9-10-17-18-5-6-13-14 | ||
曲轴的气门间隙设置位置
可选的顺时针旋向 |
|||
G3508 | 压缩冲程 | 1-3-4-8 | 1-2-7-8 |
排气冲程 | 2-5-6-7 | 3-4-5-6 | |
点火顺序 | 1-8-7-2-6-5-4-3 | ||
G3512 | 压缩冲程 | 1-3-4-6-7-12 | 1-4-5-8-9-12 |
排气冲程 | 2-5-8-9-10-11 | 2-3-6-7-10-11 | |
点火顺序 | 1-4-9-8-5-2-11-10-3-6-7-12 | ||
G3516 | 压缩冲程 | 1-2-5-6-7-8-13-14 | 1-2-3-4-5-6-9-10 |
排气冲程 | 3-4-9-10-11-12-15-16 | 7-8-11-12-13-14-15-16 | |
点火顺序 | 1-6-5-4-3-10-9-16-15-12-11-14-13-8-7-2 | ||
G3520 | 压缩冲程 | 1-2-5-6-9-11-12-13-14-17-18 | 1-2-5-6-9-11-12-13-14-17-18 |
排气冲程 | 3-4-7-8-10-15-16-19-20 | 5-6-7-9-10-14-17-18,19-20 | |
点火顺序 | 1-12-11-4-3-16-15-8-7-20-19-10-9-18-17-6-5-14-13-2 |
Show/hide table
(1) | 将 1 号活塞置于上止点 (TC) 位置,确定正确冲程。 请参阅测试和调整, "查找 1 号活塞上止点位置"。 找到某一冲程的上死点(TC)位置,并对相应的气缸进行调整。 拆下正时螺栓。 沿发动机正常旋转方向将飞轮转动 360 度。 这样就会将 1 号活塞置于与其另外一个冲程对应的上止点 (TC) 位置。 将正时螺栓安装到飞轮中,然后完成针对其余气缸的调整。 |
Caterpillar Information System:
3500B and 3500B High Displacement Generator Set Engines Ether Control System
G3500 Engines Gas Pressure
G3500 Engines Carburetor - Adjust
G3500 Engines General Information (Fuel System)
C-10, C-12, C-15 and C-16 Industrial Engines E100 Low Engine Oil Pressure Warning
C-10, C-12, C-15 and C-16 Industrial Engines E040 Low Engine Oil Pressure Shutdown
G3500 Engines Measuring Engine Oil Pressure
3512B Marine Auxiliary Engine Emergency Stop Switch
G3408 and G3412 Engines Gas Engine Ignition
G3408C and G3412C Engines Related Components
3512B Marine Auxiliary Engine Electrical Power Supply
G3500 Engines Camshaft
3034 Marine Engine - Installation Guide Engine Room Ventilation
3034 Marine Engine - Installation Guide Engine Cooling System
3512B Marine Auxiliary Engine Emergency Stop Switch (Remote)
3034 Industrial Engine Fuel System - Prime
G3500 Engines Measuring Inlet Manifold Temperature
3512B Marine Auxiliary Engine Engine Control Switch (ECS)
G3500 Engines Ignition Transformer
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply System Controller Board - Remove and Install
G3500 Engines Engine Speed/Timing Sensor
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Fan Monitor Board - Remove and Install
G3500 Engines Detonation Sensor
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Field Coil Driver Board - Remove and Install