Electric Starting Motor - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Loctite 242 | - |
- Open the left rear access door.
Show/hide table
Illustration 1 g02301942 - Turn battery disconnect switch (1) to the OFF position.
Show/hide table
Illustration 2 g02301635 - Remove bolts (2) and plate assembly (3).
Show/hide table
Illustration 3 g02301638 - Disconnect harness assembly (5), ground strap (6), and cable assembly (4).
- Use two people in order to remove electric starting motor (7). The weight of electric starting motor (7) is approximately
35 kg (77 lb) . Remove bolts (8) and electric starting motor (7).
- Install electric starting motor (7) in the reverse order of removal.
- Tighten ground strap (6) to a torque of
31 ± 4 N·m (23 ± 3 lb ft) . - Tighten cable assembly (4) to a torque of
31 ± 4 N·m (23 ± 3 lb ft) . - Apply Tooling (A) to the threads of bolts (2).
- Tighten ground strap (6) to a torque of
Caterpillar Information System:
349F and 352F Excavators Engine Supplement Alternator - Remove and Install
320D Excavators Maintenance Interval Schedule
349F and 352F Excavators Engine Supplement Nozzle Heater Harness - Remove and Install - Harness Assembly
Engine Speed Drop and Low Boost on Certain 324E and 329E Excavators{1000, 1058, 1907} Engine Speed Drop and Low Boost on Certain 324E and 329E Excavators{1000, 1058, 1907}
2013/08/12 New Software Is Now Available With The Cat Product Link-Japan On Certain Excavators {7610, 7620}
326F, 329F and 330F Excavators Machine Systems Stick Bearings and Seals - Install
MD6310 Rotary Blasthole Drill Machine Systems Shuttle Valve
374F Excavator Fuel System Secondary Filter - Replace
Adaptive Control System Valve ECM Flashing Problems with 336E H Excavators When Equipped with Product Link PL522{7610, 7620} Adaptive Control System Valve ECM Flashing Problems with 336E H Excavators When Equipped with Product Link PL522{7610, 7620}
2013/08/15 New Software For Cat® ET Can Now Be Used For All Caterpillar Products {0785, 7606}
349F and 352F Excavators Relay - Test
349F and 352F Excavators Electrical Power Supply - Test
349F and 352F Excavators Engine Supplement Fuel Transfer Pump - Remove and Install
349F and 352F Excavators Engine Supplement Fuel Manifold - Remove and Install - Clean Emissions Manifold
349F and 352F Excavators Engine Supplement Relay (ARD Nozzle Heater) - Remove and Install - Clean Emissions Module
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Lifter Group
311F Excavator Machine Systems Blade Hydraulic System
311F Excavator Machine Systems Blade Hydraulic System
Procedure to Repair Spill Guard on the Bucket Groups for 938H Through 980K Medium Wheel Loaders {0679, 6101} Procedure to Repair Spill Guard on the Bucket Groups for 938H Through 980K Medium Wheel Loaders {0679, 6101}
2013/08/19 An Improved Spill Guard Bucket is Being Used on 938H Wheel Loaders {0679, 6101}
349F and 352F Excavators Engine Supplement Ignition Coil - Remove and Install - Clean Emissions Module
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Fuel Transfer Pump
349F and 352F Excavators Sensor Signal (Analog, Passive) - Test
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Engine Oil Pressure