Customer Specified Parameters Table
Show/hide table
Customer Specified Parameters     | ||
---|---|---|
ECM Parameter     | Possible Values     | Default Value     |
ECM Identification Parameter     | ||
Equipment ID     | 17 Digits Available characters are dependent on the service tool that is used     |
Not Programmed     |
Engine Configuration Parameter     | ||
Ether Solenoid Configuration     | Not Installed Continuous Flow Solenoid     |
Not Installed     |
Engine Warmup Elevated Idle Feature Enable Status     | Enabled Disabled     |
Enabled     |
Engine Warmup Elevated Idle Delay Time     | 3 to 30 minutes     | 10 minutes     |
Low System Battery Voltage Elevated Idle     | Enabled Disabled     |
Enabled     |
Engine Idle Shutdown     | ||
Minimum Ambient Air Temperature     | 0 to 29 degrees C     | 0 degrees C     |
Maximum Ambient Air Temperature     | 30 to 100 degrees C     | 30 degrees C     |
Shutdown Enable Status     | Disabled Enabled     |
Disabled     |
Engine Idle Shutdown Delay Time     | 1 to 60 minutes     | 5 minutes     |
Engine Idle Shutdown Ambient Temperature Override Enable Status     | Disabled Enabled     |
Enabled     |
Delayed Engine Shutdown     | ||
Delayed Engine Shutdown Enable Status     | Disabled Enabled     |
Enabled     |
Delayed Engine Shutdown Maximum Time     | 1 to 10 minutes     | 5 minutes     |
Engine Fan Control     | ||
Engine Fan Type Configuration     | Viscous Clutch Direct Drive Variable Pitch     |
Viscous Clutch     |
Engine Fan Cooling Map     | Standard High Ambient     |
Standard     |
Aftertreatment Configuration     | ||
ARD Auto Regeneration Enable Status     | Disabled Enabled     |
Enabled     |
Key Off Regeneration Enable Status     | Enabled Disabled     |
Enabled     |
Key Off Aftertreatment Regeneration Maximum Time     | 5 to 25 minutes     | 15 minutes     |
Factory Installed Aftertreatment #1 Identification Number     | Programmed Not Programmed     |
Not Programmed     |
DPF #1 Soot Loading Sensing System Configuration Code     | 20(Hex) to 7F(Hex)     | 0     |
High Soot Load Aftertreatment Protection     | Disabled Enabled     |
Disabled     |
System Settings     | ||
System Operating Voltage Configuration     | 12 VDC 24 VDC     |
24 VDC     |
Security Access Parameters     | ||
CAN Communication Protocol Write Security     | Seed and Key No Security     |
Seed and Key     |
CAN Communication Protocol Read Security     | Seed and Key No Security     |
Seed and Key     |
Caterpillar Information System:
450F Backhoe Loader Fuel System Secondary Filter - Replace
C7.1 Engines For Caterpillar Built Machines Customer Specified Parameters
300.9D VPS Mini Hydraulic Excavator Machine Systems Stick Cylinder
C9.3 Engines for Caterpillar Built Machines ECM - Replace
C9.3 Engines for Caterpillar Built Machines Exhaust System Contains Oil
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Tool Bushing (Lower)
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Hydraulic Oil Flow - Test
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Work Tool Troubleshooting Information
Automatic Lubrication System for Large Hydraulic Hammers General Information
C9.3 Engines for Caterpillar Built Machines Engine Shutdown Occurs Intermittently
300.9D and 300.9D VPS Mini Hydraulic Excavator Capacities (Refill)
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve
320E Excavator Specifications
312E Excavator Boom/Stick/Bucket Combinations
312E Excavator Declaration of Conformity
312F and 313F Excavators Sound Information and Vibration Information
320E Excavator Declaration of Conformity
312E Excavator Capacities (Refill)
440 and 450 Backhoe Loader Engine Oil Sample - Obtain
2011/03/04 A New Cover for the Fuel Transfer Pump Is Used on Certain Machines {1256}
320E Excavator Boom/Stick/Bucket Combinations
320E Excavator Safety Messages
M316D, M318D and M322D Wheeled Excavators Machine Systems System Pressure - Release
2011/08/05 Improved Track Roller Group is Now Used for Certain 325D Excavators {4180}