Governor Drive
Show/hide table
Illustration 1 | g00932394 |
(A-A) Rear view (B-B) Front view |
Show/hide table
Illustration 2 | g00932397 |
Section A-A |
(1) Bearing
-
The bearing must be flush with the inside surface of the front housing.
- Bore in bearing ... 9.615 ± 0.010 mm (0.3785 ± 0.0004 inch)
- Diameter of shaft ... 9.503 ± 0.013 mm (0.3741 ± 0.0005 inch)
(2) Bearing
-
The bearing must be flush with the inside surface of the front housing.
- Bore in bearing ... 18.974 ± 0.025 mm (0.7470 ± 0.0010 inch)
(A) Protrusion of the shaft from the inside surface of the front housing ... 3.0 ± 0.2 mm (0.118 ± 0.008 inch)
- Diameter of shaft ... 18.839 ± 0.013 mm (0.7417 ± 0.0005 inch)
(3) Bearing
-
The bearing must be flush with the inside surface of the front housing.
- Bore in bearing ... 12.802 ± 0.127 mm (0.5040 ± 0.0050 inch)
- Diameter of shaft ... 18.839 ± 0.013 mm (0.7417 ± 0.0005 inch)
(4) Nut
Apply 4C-4030 Thread Lock Compound to the nut's threads.
Show/hide table
Illustration 3 | g00932399 |
Section B-B |
(5) Bushing
- Bore in bushing ... 25.1142 ± 0.0191 mm (0.98875 ± 0.00075 inch)
(6) Sleeve
- Outer diameter of sleeve ... 24.958 ± 0.013 mm (0.9826 ± 0.0005 inch)
Show/hide table
Illustration 4 | g00932400 |
Left view |
(7) Cover
Use solvent to thoroughly clean the mating surfaces of the cover and of the governor drive's rear housing. Apply 4C-5300 Gasket Sealant to the joint and install the cover within ten minutes.
After the governor drive is assembled, fill the interior cavity with engine oil prior to the first start-up.
Caterpillar Information System:
3508B Industrial Engines Testing the Radiator and Cooling System for Leaks
3500B and 3500B High Displacement Generator Set Engines Testing the Cooling System
G3406 Engines Spark Plug and Transformer
3524B Engines for 797 and 797B Off-Highway Trucks General Information (Electronic Control System)
G3406 and G3412 Generator Set Engines Ignition Transformer
G3406 Engines Spark Plug Adapter
3500B and 3500B High Displacement Generator Set Engines Engine Speed Sensor
3500B and 3500B High Displacement Generator Set Engines Starting Motor
3500B and 3500B High Displacement Generator Set Engines Starting Solenoid
3500B and 3500B High Displacement Generator Set Engines Alternator
3508B Engine for Caterpillar Built Machines Camshaft
3508B Industrial Engines Crankshaft
SPS342 Skid Mounted Pumper Batteries - Replace
C-10 and C-12 Industrial Engines Water Pump
3054, 3054B and 3056 Marine Engines Refill Capacities
2000/09/01 New Injector Wiring Harnesses Are Color Coded {1251, 1408}
G3406 Engines Governor
2000/09/01 Correction to Operation and Maintenance Manual, SEBU7074, "3306B and 3406C Generator Set Engines" {7002}
G3408C and G3412C Engines Cylinder Block, Liners and Heads
2000/09/01 New Protective Sleeve Available For Hydrax Actuator Shaft {1716}
2000/09/11 Explanation of Fuel Shutoff Solenoid Operation {1259}
G3406 Engines Governor Fastener
G3406 Engines Governor Control
C-10 and C-12 Industrial Engines Electronic Control System Components