Flywheel Housing - Inspect
Show/hide table
所需工具     | ||
---|---|---|
零件号     | 零件名称     | 数量     |
8T-5096     | 千分表总成     | 1     |
飞轮壳端面跳动(轴向偏心度)
Show/hide table
图 1 | g00285931 |
8T-5096 千分表总成 |
- 将千分表固定在飞轮上,使千分表的测头接触飞轮壳的端面。
- 在每一点读取千分表的读数之前,向曲轴施加一个朝向后端的力。
- 转动飞轮,同时在位置 (A) 将千分表设置为 0.0 mm (0.00 in)。 在位置 (B) 、 (C) 和 (D) 读取千分表的读数。
Show/hide table
图 2 | g00285932 |
检查飞轮壳的端面跳动 |
- 在所有四个点测得的较低测量值和较高测量值之间的差异不得超过 0.50 mm (0.0197 in). 这些测量值是飞轮壳允许的最大端面跳动(轴向偏心度)。
飞轮壳镗孔跳动(径向偏心度)
- 将千分表固定在飞轮上,使千分表的测头接触飞轮壳的镗孔表面。
Show/hide table
图 3 | g00285934 |
8T-5096 千分表 |
- 转动飞轮,同时在位置 (A) 将千分表设置为 0.0 mm (0.00 in)。 在位置 (B) 、 (C) 和 (D) 读取千分表的读数。
Show/hide table
图 4 | g00285932 |
检查飞轮壳的镗孔跳动 |
- 在所有四个点测得的较低测量值和较高测量值之间的差异不得超过 0.50 mm (0.0197 in). 这些测量值是飞轮壳允许的最大端面跳动(轴向偏心度)。
Caterpillar Information System:
C4.2 and C6.4 Engines for Caterpillar Built Machines Flywheel - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Piston Height - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Cylinder Head - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Connecting Rod - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Engine Oil Pump - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Engine Oil Pressure - Test
M313D, M315D, M316D, M318D and M322D Excavators and M318D MH and M322D MH Material Handlers Lifting Capacities - M316D Excavator with a Offset Boom (Heavy Lift Option)
2007/04/16 New Software for the Auxiliary Hydraulic Circuits Is Available {7610, 7620}
2007/06/18 A New Idler Pulley Is Available for the Engine Pulley Group {1361}
Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064} Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064}
C4.2 and C6.4 Engines for Caterpillar Built Machines Compression - Test
C4.2 and C6.4 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
M313D, M315D, M316D, M318D and M322D Excavators and M318D MH and M322D MH Material Handlers Lifting Capacities - M318D MH Excavator
M313D, M315D, M316D, M318D and M322D Excavators and M318D MH and M322D MH Material Handlers Lifting Capacities - M322D MH Excavator
2007/04/23 Shut Off Valves Lock the Thumb of Backhoe Loaders {1329, 6547}
R2900G Load Haul Dump Bucket Control Group Safety Pins
C15 and C18 Petrolem Generator Set Engines General Information
385B and 5090B Excavators Excavator Systems Swing Gear and Bearing - Remove
584 and 584HD Forwarders Visibility Information
2007/05/14 New Screws for the Door Hinge on the Cab {7308}
330D and 336D Excavators and 330D Material Handlers Machine System Specifications Boom Lines
323D MHPU Mobile Hydraulic Power Unit Swing Bearing - Lubricate
330D Forest Machine Machine Systems Load Control Valve (Boom Cylinder) - Install
VT-30, VT-40, VT-50 and VT-60 Multi Processors Hydraulic Cylinder - Disassemble