Piston Height - Inspect
如果活塞高于缸体的高度不在技术规格单元, "活塞和活塞环"中规定的公差范围内,则必须更换活塞和活塞销轴承。 如果更换或重新加工过以下任一部件,则必须测量活塞高于缸体的高度:
- 曲轴
- 缸盖
- 连杆
- 活塞销轴承
- 活塞
必须保持适当的活塞高度才能确保发动机符合排放标准的要求。
注: 活塞顶部不应进行机加工。 如果安装的是原来的活塞,确保将原来的活塞装配到正确的连杆再安装到原来的油缸中。
Show/hide table
图 1 | g01432459 |
8T-0455 缸套凸出量工具总成 (1) 1P-2403 千分表 (2) 1P-2402 量规体 (3) 1P-5507 仪表支座 |
- 使用 8T-0455 缸套凸出量工具总成 以测量活塞高于缸体的高度。 使用仪表支座 (3) 将缸体表面的千分表 (1) 归零。
- 确定缸体上仪表支座 (3) 的位置。 转动曲轴,直到活塞处于上止点附近。 确保缸套的火花环不会影响仪表支座或千分表。
Caterpillar Information System:
C4.2 and C6.4 Engines for Caterpillar Built Machines Cylinder Head - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Connecting Rod - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Engine Oil Pump - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Engine Oil Pressure - Test
M313D, M315D, M316D, M318D and M322D Excavators and M318D MH and M322D MH Material Handlers Lifting Capacities - M316D Excavator with a Offset Boom (Heavy Lift Option)
2007/04/16 New Software for the Auxiliary Hydraulic Circuits Is Available {7610, 7620}
2007/06/18 A New Idler Pulley Is Available for the Engine Pulley Group {1361}
Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064} Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064}
C4.2 and C6.4 Engines for Caterpillar Built Machines Compression - Test
C4.2 and C6.4 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Fuel System - Prime
321D LCR Excavator Lifting Capacities
C4.2 and C6.4 Engines for Caterpillar Built Machines Flywheel - Inspect
C4.2 and C6.4 Engines for Caterpillar Built Machines Flywheel Housing - Inspect
M313D, M315D, M316D, M318D and M322D Excavators and M318D MH and M322D MH Material Handlers Lifting Capacities - M318D MH Excavator
M313D, M315D, M316D, M318D and M322D Excavators and M318D MH and M322D MH Material Handlers Lifting Capacities - M322D MH Excavator
2007/04/23 Shut Off Valves Lock the Thumb of Backhoe Loaders {1329, 6547}
R2900G Load Haul Dump Bucket Control Group Safety Pins
C15 and C18 Petrolem Generator Set Engines General Information
385B and 5090B Excavators Excavator Systems Swing Gear and Bearing - Remove
584 and 584HD Forwarders Visibility Information
2007/05/14 New Screws for the Door Hinge on the Cab {7308}
330D and 336D Excavators and 330D Material Handlers Machine System Specifications Boom Lines
323D MHPU Mobile Hydraulic Power Unit Swing Bearing - Lubricate