Lifting Capacities - M315C Excavator with a One-Piece Boom (Wide Axle and Wide Dozer)
Note: These lifting capacity tables are for typical options.
Note: For more information on your specific configuration, see your dealer.
Note: The lifting capacities in the following tables represent the maximum lifting capacities. Each machine is configured differently. The following options require additional tables for lifting capacities:
- Heavy lift
- Additional counterweights
- Optional buckets
- Optional sticks
- Quick coupler
The following conditions affect the lifting capacities:
(A) - The rear dozer is up.
(B) - The rear dozer is down. The lifting capacity is over the rear.
(C) - The rear stabilizers are down. The lifting capacity is over the rear.
(D) - The front and rear stabilizers are down.
(E) - The rear dozer and front stabilizers are down.
(F) - Front Load
(S) - Side Load
Show/hide table
| M315C Excavator with a One-Piece Boom, 2.1 m (6.9 ft) stick and a quick coupler Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 3.8 | 2.6 | |||||||||
| B | 4.1 (1) | 3.0 | ||||||||||
| C | 3.5 | |||||||||||
| D | 4.1 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 5.3 (1) | 4.1 | 3.8 | 2.6 | |||||||
| B | 4.8 | 4.5 (1) | 3.0 | |||||||||
| C | 5.3 (1) | 3.5 | ||||||||||
| D | 4.5 (1) | |||||||||||
| E | 4.3 | |||||||||||
| 3.0 m | A | 5.8 | 3.8 | 3.7 | 2.5 | 2.4 (1) | 1.6 | 7.90 | ||||
| B | 6.3 (1) | 4.5 | 4.9 (1) | 2.9 | 1.9 | |||||||
| C | 5.2 | 3.3 | 2.2 | |||||||||
| D | 6.3 (1) | 4.8 | 2.4 (1) | |||||||||
| E | 4.2 | |||||||||||
| 1.5 m | A | 5.5 | 3.5 | 3.5 | 2.4 | 2.5 | 1.7 | 2.3 | 1.5 | 8.01 | ||
| B | 7.2 (1) | 4.2 | 5.2 (1) | 2.8 | 3.7 (1) | 2.0 | 2.5 (1) | 1.8 | ||||
| C | 4.9 | 5.2 | 3.2 | 3.6 | 2.3 | 2.1 | ||||||
| D | 7.2 (1) | 5.2 (1) | 4.6 | 3.7 (1) | 3.3 | 2.5 (1) | ||||||
| E | 6.2 | 4.0 | 2.9 | |||||||||
| 0.0 m | A | 5.3 | 3.4 | 3.4 | 2.3 | 2.4 | 1.6 | 7.79 | ||||
| B | 7.3 (1) | 4.0 | 5.3 (1) | 2.7 | 2.7 (1) | 1.8 | ||||||
| C | 4.7 | 5.1 | 3.1 | 2.2 | ||||||||
| D | 7.1 | 5.3 (1) | 4.5 | 2.7 (1) | ||||||||
| E | 6.1 | 3.9 | 2.7 | |||||||||
| -1.5 m | A | 7.4 (1) | 6.3 | 5.2 | 3.4 | 3.4 | 2.2 | 2.7 | 1.8 | 7.21 | ||
| B | 7.4 (1) | 6.7 (1) | 4.0 | 4.8 (1) | 2.6 | 3.1 (1) | 2.1 | |||||
| C | 4.7 | 3.1 | 2.4 | |||||||||
| D | 6.7 (1) | 4.5 | 3.1 (1) | |||||||||
| E | 6.0 | 3.9 | 3.0 | |||||||||
| -3.0 m | A | 6.9 (1) | 6.4 | 5.2 (1) | 3.4 | 3.0 (1) | 2.3 | 6.15 | ||||
| B | 6.9 (1) | 4.1 | 2.7 | |||||||||
| C | 4.8 | 3.0 (1) | ||||||||||
| D | 5.2 (1) | |||||||||||
| E | ||||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a One-Piece Boom, 2.1 m (6.9 ft) stick and a quick coupler 400 kg Additional Counterweight Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 4.0 | 2.8 | |||||||||
| B | 4.1 (1) | 3.2 | ||||||||||
| C | 3.7 | |||||||||||
| D | 4.1 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 5.3 (1) | 4.4 | 4.0 | 2.8 | |||||||
| B | 5.1 | 4.5 (1) | 3.2 | |||||||||
| C | 5.3 (1) | 3.7 | ||||||||||
| D | 4.5 (1) | |||||||||||
| E | ||||||||||||
| 3.0 m | A | 6.1 | 4.1 | 3.9 | 2.7 | 2.4 (1) | 1.7 | 7.90 | ||||
| B | 6.3 (1) | 4.7 | 4.9 (1) | 3.1 | 2.0 | |||||||
| C | 5.5 | 3.5 | 2.3 | |||||||||
| D | 6.3 (1) | 4.9 (1) | 2.4 (1) | |||||||||
| E | 4.4 | |||||||||||
| 1.5 m | A | 5.8 | 3.8 | 3.8 | 2.5 | 2.7 | 1.8 | 2.5 | 1.7 | 8.01 | ||
| B | 7.2 (1) | 4.5 | 5.2 (1) | 2.9 | 3.7 (1) | 2.1 | 2.5 (1) | 1.9 | ||||
| C | 5.2 | 3.4 | 2.4 | 2.2 | ||||||||
| D | 7.2 (1) | 4.9 | 3.5 | 2.5 (1) | ||||||||
| E | 6.6 | 4.3 | 3.0 | |||||||||
| 0.0 m | A | 5.6 | 3.6 | 3.7 | 2.4 | 2.5 | 1.7 | 7.79 | ||||
| B | 7.3 (1) | 4.3 | 5.3 (1) | 2.9 | 2.7 (1) | 2.0 | ||||||
| C | 5.0 | 3.3 | 2.3 | |||||||||
| D | 7.3 (1) | 4.8 | 2.7 (1) | |||||||||
| E | 6.4 | 4.2 | ||||||||||
| -1.5 m | A | 7.4 (1) | 6.7 | 5.6 | 3.6 | 3.6 | 2.4 | 2.8 | 1.9 | 7.21 | ||
| B | 7.4 (1) | 6.7 (1) | 4.3 | 4.8 (1) | 2.8 | 3.1 (1) | 2.2 | |||||
| C | 5.0 | 3.3 | 2.6 | |||||||||
| D | 6.7 (1) | 4.8 | 3.1 (1) | |||||||||
| E | 6.4 | 4.1 | ||||||||||
| -3.0 m | A | 6.9 (1) | 6.9 | 5.2 (1) | 3.7 | 3.0 (1) | 2.4 | 6.15 | ||||
| B | 6.9 (1) | 4.3 | 2.8 | |||||||||
| C | 5.1 | 3.0 (1) | ||||||||||
| D | 5.2 (1) | |||||||||||
| E | ||||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a One-Piece Boom, 2.4 m (7.9 ft) stick and a quick coupler Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 3.9 | 2.7 | |||||||||
| B | 4.0 (1) | 3.1 | ||||||||||
| C | 3.5 | |||||||||||
| D | 4.0 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 3.8 | 2.6 | |||||||||
| B | 4.3 (1) | 3.0 | ||||||||||
| C | 3.5 | |||||||||||
| D | 4.3 (1) | |||||||||||
| E | ||||||||||||
| 3.0 m | A | 5.8 | 3.9 | 3.7 | 2.5 | 2.6 | 1.7 | 2.1 (1) | 1.5 | 8.16 | ||
| B | 6.1 (1) | 4.5 | 4.7 (1) | 2.9 | 3.7 (1) | 2.0 | 1.8 | |||||
| C | 5.2 | 3.3 | 2.3 | 2.1 | ||||||||
| D | 6.1 (1) | 4.7 (1) | 3.3 | 2.1 (1) | ||||||||
| E | 4.2 | 2.9 | ||||||||||
| 1.5 m | A | 5.5 | 3.6 | 3.5 | 2.4 | 2.5 | 1.7 | 2.2 | 1.4 | 8.27 | ||
| B | 7.0 (1) | 4.2 | 5.1 (1) | 2.8 | 4.1 (1) | 1.9 | 2.2 (1) | 1.7 | ||||
| C | 4.9 | 3.2 | 3.6 | 2.3 | 2.0 | |||||||
| D | 7.0 (1) | 4.6 | 4.1 (1) | 3.3 | 2.2 (1) | |||||||
| E | 6.3 | 4.0 | 2.9 | |||||||||
| 0.0 m | A | 3.7 (1) | 5.3 | 3.4 | 3.4 | 2.2 | 2.5 | 1.6 | 2.2 | 1.5 | 8.05 | |
| B | 7.3 (1) | 4.0 | 5.3 (1) | 2.6 | 3.9 (1) | 1.9 | 2.4 (1) | 1.7 | ||||
| C | 4.7 | 5.1 | 3.1 | 3.6 | 2.2 | 2.0 | ||||||
| D | 7.1 | 5.3 (1) | 4.5 | 3.9 (1) | 3.2 | 2.4 (1) | ||||||
| E | 6.1 | 3.9 | 2.8 | |||||||||
| -1.5 m | A | 7.2 (1) | 6.2 | 5.2 | 3.3 | 3.4 | 2.2 | 2.5 | 1.6 | 7.50 | ||
| B | 7.2 (1) | 6.8 (1) | 3.9 | 4.9 (1) | 2.6 | 2.8 (1) | 1.9 | |||||
| C | 4.6 | 3.0 | 2.2 | |||||||||
| D | 6.8 (1) | 4.5 | 2.8 (1) | |||||||||
| E | 6.0 | 3.9 | ||||||||||
| -3.0 m | A | 7.6 (1) | 6.3 | 5.3 | 3.4 | 3.5 | 2.3 | 3.1 (1) | 2.1 | 6.49 | ||
| B | 7.6 (1) | 5.5 (1) | 4.0 | 3.6 (1) | 2.7 | 2.4 | ||||||
| C | 4.7 | 3.1 | 2.8 | |||||||||
| D | 5.5 (1) | 3.6 (1) | 3.1 (1) | |||||||||
| E | ||||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a One-Piece Boom, 2.4 m (7.9 ft) stick and a quick coupler 400 kg Additional Counterweight Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 4.0 (1) | 2.8 | |||||||||
| B | 3.3 | |||||||||||
| C | 3.7 | |||||||||||
| D | 4.0 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 4.0 | 2.8 | |||||||||
| B | 4.3 (1) | 3.2 | ||||||||||
| C | 3.7 | |||||||||||
| D | 4.3 (1) | |||||||||||
| E | ||||||||||||
| 3.0 m | A | 6.1 (1) | 4.1 | 3.9 | 2.7 | 2.7 | 1.8 | 2.1 (1) | 1.6 | 8.16 | ||
| B | 4.8 | 4.7 (1) | 3.1 | 3.7 (1) | 2.1 | 1.9 | ||||||
| C | 5.5 | 3.5 | 2.5 | 2.1 (1) | ||||||||
| D | 6.1 (1) | 4.7 (1) | 3.5 | |||||||||
| E | 4.4 | 3.1 | ||||||||||
| 1.5 m | A | 5.8 | 3.8 | 3.8 | 2.5 | 2.7 | 1.8 | 2.2 (1) | 1.6 | 8.27 | ||
| B | 7.0 (1) | 4.5 | 5.1 (1) | 2.9 | 4.1 (1) | 2.1 | 1.8 | |||||
| C | 5.2 | 3.4 | 3.8 | 2.4 | 2.1 | |||||||
| D | 7.0 (1) | 4.9 | 4.1 (1) | 3.5 | 2.2 (1) | |||||||
| E | 6.6 | 4.3 | 3.0 | |||||||||
| 0.0 m | A | 3.7 (1) | 5.6 | 3.6 | 3.6 | 2.4 | 2.6 | 1.8 | 2.4 | 1.6 | 8.05 | |
| B | 7.3 (1) | 4.3 | 5.3 (1) | 2.8 | 3.9 (1) | 2.1 | 2.4 (1) | 1.9 | ||||
| C | 5.0 | 3.3 | 3.8 | 2.4 | 2.2 | |||||||
| D | 7.3 (1) | 4.8 | 3.9 (1) | 3.4 | 2.4 (1) | |||||||
| E | 6.4 | 4.1 | 3.0 | |||||||||
| -1.5 m | A | 7.2 (1) | 6.6 | 5.5 | 3.6 | 3.6 | 2.4 | 2.7 | 1.8 | 7.50 | ||
| B | 7.2 (1) | 6.8 (1) | 4.2 | 4.9 (1) | 2.8 | 2.8 (1) | 2.1 | |||||
| C | 4.9 | 3.2 | 2.4 | |||||||||
| D | 6.8 (1) | 4.7 | 2.8 (1) | |||||||||
| E | 6.3 | 4.1 | ||||||||||
| -3.0 m | A | 7.6 (1) | 6.8 | 5.5 (1) | 3.6 | 3.6 (1) | 2.4 | 3.1 (1) | 2.2 | 6.49 | ||
| B | 7.6 (1) | 4.3 | 2.9 | 2.6 | ||||||||
| C | 5.0 | 3.3 | 3.0 | |||||||||
| D | 5.5 (1) | 3.6 (1) | 3.1 (1) | |||||||||
| E | ||||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a One-Piece Boom, 2.6 m (8.5 ft) stick and a quick coupler Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 3.9 (1) | 2.7 | |||||||||
| B | 3.1 | |||||||||||
| C | 3.5 | |||||||||||
| D | 3.9 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 3.8 | 2.6 | 2.3 (1) | 1.8 | |||||||
| B | 4.2 (1) | 3.0 | 2.0 | |||||||||
| C | 3.5 | 2.3 (1) | ||||||||||
| D | 4.2 (1) | |||||||||||
| E | ||||||||||||
| 3.0 m | A | 5.9 (1) | 3.9 | 3.7 | 2.5 | 2.6 | 1.7 | 1.9 (1) | 1.5 | 8.36 | ||
| B | 4.6 | 4.6 (1) | 2.9 | 3.9 (1) | 2.0 | 1.7 | ||||||
| C | 5.3 | 3.4 | 3.7 | 2.3 | 1.9 (1) | |||||||
| D | 5.9 (1) | 4.6 (1) | 3.9 (1) | 3.4 | ||||||||
| E | 4.2 | 2.9 | ||||||||||
| 1.5 m | A | 5.5 | 3.6 | 3.6 | 2.4 | 2.5 | 1.7 | 2.0 (1) | 1.4 | 8.46 | ||
| B | 6.9 (1) | 4.2 | 5.1 (1) | 2.8 | 4.1 (1) | 2.0 | 1.6 | |||||
| C | 4.9 | 3.2 | 3.6 | 2.3 | 1.9 | |||||||
| D | 6.9 (1) | 4.6 | 4.1 (1) | 3.3 | 2.0 (1) | |||||||
| E | 6.3 | 4.0 | 2.9 | |||||||||
| 0.0 m | A | 3.9 (1) | 5.3 | 3.4 | 3.4 | 2.3 | 2.5 | 1.6 | 2.2 | 1.4 | 8.25 | |
| B | 7.3 (1) | 4.0 | 5.3 (1) | 2.7 | 4.0 (1) | 1.9 | 2.2 (1) | 1.7 | ||||
| C | 4.7 | 5.1 | 3.1 | 3.6 | 2.2 | 2.0 | ||||||
| D | 7.1 | 5.3 (1) | 4.5 | 4.0 (1) | 3.2 | 2.2 (1) | ||||||
| E | 6.1 | 3.9 | 2.8 | |||||||||
| -1.5 m | A | 7.0 (1) | 6.2 | 5.2 | 3.3 | 3.4 | 2.2 | 2.4 | 1.6 | 7.71 | ||
| B | 7.0 (1) | 7.0 (1) | 3.9 | 5.0 (1) | 2.6 | 2.6 (1) | 1.8 | |||||
| C | 4.6 | 3.0 | 2.2 | |||||||||
| D | 7.0 (1) | 4.5 | 2.6 (1) | |||||||||
| E | 6.0 | 3.9 | ||||||||||
| -3.0 m | A | 8.1 (1) | 6.3 | 5.3 | 3.4 | 3.4 | 2.2 | 2.9 | 1.9 | 6.74 | ||
| B | 7.6 | 5.8 (1) | 4.0 | 3.9 (1) | 2.6 | 3.1 (1) | 2.3 | |||||
| C | 8.1 (1) | 4.7 | 3.1 | 2.6 | ||||||||
| D | 5.8 (1) | 3.9 (1) | 3.1 (1) | |||||||||
| E | 3.9 | |||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Show/hide table
| M315C Excavator with a One-Piece Boom, 2.6 m (8.5 ft) stick and a quick coupler 400 kg Additional Counterweight Lifting Capacities in Metric Tons |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Radius | 3.0 m | 4.5 m | 6.0 m | 7.5 m | Maximum Reach | |||||||
| Load Point Height | F | S | F | S | F | S | F | S | F | S | m | |
| 6.0 m | A | 3.9 (1) | 2.9 | |||||||||
| B | 3.3 | |||||||||||
| C | 3.8 | |||||||||||
| D | 3.9 (1) | |||||||||||
| E | ||||||||||||
| 4.5 m | A | 4.1 | 2.8 | 2.3 (1) | 1.9 | |||||||
| B | 4.2 (1) | 3.2 | 2.2 | |||||||||
| C | 3.7 | 2.3 (1) | ||||||||||
| D | 4.2 (1) | |||||||||||
| E | ||||||||||||
| 3.0 m | A | 5.9 (1) | 4.2 | 3.9 | 2.7 | 2.7 | 1.9 | 1.9 (1) | 1.6 | 8.36 | ||
| B | 4.8 | 4.6 (1) | 3.1 | 3.9 (1) | 2.2 | 1.8 | ||||||
| C | 5.6 | 3.6 | 2.5 | 1.9 (1) | ||||||||
| D | 5.9 (1) | 4.6 (1) | 3.5 | |||||||||
| E | 4.4 | 3.1 | ||||||||||
| 1.5 m | A | 5.8 | 3.8 | 3.8 | 2.5 | 2.7 | 1.8 | 2.0 (1) | 1.5 | 8.46 | ||
| B | 6.9 (1) | 4.5 | 5.1 (1) | 3.0 | 4.1 (1) | 2.1 | 1.8 | |||||
| C | 5.2 | 3.4 | 3.8 | 2.4 | 2.0 (1) | |||||||
| D | 6.9 (1) | 4.9 | 4.1 (1) | 3.5 | ||||||||
| E | 6.6 | 4.3 | 3.0 | |||||||||
| 0.0 m | A | 3.9 (1) | 5.6 | 3.6 | 3.7 | 2.4 | 2.6 | 1.8 | 2.2 (1) | 1.5 | 8.25 | |
| B | 7.3 (1) | 4.3 | 5.3 (1) | 2.8 | 4.0 (1) | 2.1 | 1.8 | |||||
| C | 5.0 | 3.3 | 3.8 | 2.4 | 2.1 | |||||||
| D | 7.3 (1) | 4.8 | 4.0 (1) | 3.4 | 2.2 (1) | |||||||
| E | 6.4 | 4.1 | 3.0 | |||||||||
| -1.5 m | A | 7.0 (1) | 6.6 | 5.5 | 3.6 | 3.6 | 2.4 | 2.5 | 1.7 | 7.71 | ||
| B | 7.0 (1) | 7.0 (1) | 4.2 | 5.0 (1) | 2.8 | 2.6 (1) | 2.0 | |||||
| C | 4.9 | 3.2 | 2.3 | |||||||||
| D | 7.0 (1) | 4.7 | 2.6 (1) | |||||||||
| E | 6.3 | 4.1 | ||||||||||
| -3.0 m | A | 8.1 (1) | 6.7 | 5.6 | 3.6 | 3.6 | 2.4 | 3.1 (1) | 2.1 | 6.74 | ||
| B | 8.1 (1) | 5.8 (1) | 4.3 | 3.9 (1) | 2.8 | 2.4 | ||||||
| C | 5.0 | 3.3 | 2.8 | |||||||||
| D | 5.8 (1) | 3.9 (1) | 3.1 (1) | |||||||||
| E | ||||||||||||
Show/hide table
| ( 1 ) | Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities. |
Caterpillar Information System:
2004/12/27 Cat Track Torque Wrench is Available for the Removal of Track Bolts and for the Installation of Track Bolts {0729, 0765}
318C and 319C Excavators Machine System Specifications Stick
345C MHPU Mobile Hydraulic Power Unit Engine Starting
2004/07/05 249-2813 Water Filter Gp is Available for Shop Applications that Require Water Filtration {0699}
318C and 319C Excavators Machine System Specifications Stick
320D Excavator Fuel Tank Water and Sediment - Drain
325D and 329D Excavators Fuel Tank Shutoff and Drain Control
2004/06/21 The Bearing Assembly for the Idle Pulley is Now Serviceable {1358}
385C Excavator and 385C MHPU Mobile Hydraulic Power Unit Automatic Engine Speed Control (AEC)
385C Excavator and 385C MHPU Mobile Hydraulic Power Unit Travel Speed Control
325C Excavator Engine Speed Control
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
325D and 329D Excavators Engine and Machine Warm-Up
325D and 329D Excavators Operation Information
2004/06/28 210-6990 Pressure Gauge (LCD Display, 0 to 500-PSI) Is Available for Use by Technicians {0770}
325D and 329D Excavators Indicators and Gauges - Test
2004/07/05 243-3133 Quick Connect Coupler (Fluid Sampling) Provides A Coupler for Portable Particle Analyzers {0707, 0717, 0731, 0732, 0738}
2004/06/21 A New Washer Prevents Oil Leakage From The Hydraulic Pump {507G, 5084}
2004/06/14 An Improved Bushing is Now Available for Mini Hydraulic Excavators {6508}
2004/06/14 New Harder Cylinder Pistons Are Available {5456, 5457, 5458}
C13, C15, and C18 Tier 4 Final Engines Exhaust Manifold
2004/06/01 A New Special Instruction, REHS2259 , "Fabricated Tool for Alternate Method of Tightening Fan Drive Belts" is Available {1357, 1397}
Supplemental Product Support Literature for the Field Installation of a 20 kW Right Front Corner Mounted Generator Set ( 223-4514 Hydraulic Generator Arrangement) and Operation Instructions {1404, 4450, 5050, 7000} Supplemental Product Support Literature for the Field Installation of a 20 kW Right Front Corner Mounted Generator Set ( 223-4514 Hydraulic Generator Arrangement) and Operation Instructions {1404, 4450, 5050, 7000}
2006/02/13 Two Adjustment Gauges Help the Technician Set the Lash for the Variable Valve Actuators {0703, 0763, 1100, 1209}