CID 0042 FMI 06 Injector Actuation Valve short to ground
Conditions Which Generate This Code:
The Electronic Control Module (ECM) detects all of the following conditions:
- The ECM reads a short circuit to the injection actuation pressure control valve (IAPCV).
- Desired current is greater than 0.2 Amps.
- The ECM has been powered for at least three seconds.
- Battery voltage is greater than 9.0 VDC for two seconds.
- The engine is not cranking.
System Response:
The ECM will log the diagnostic code. The diagnostic code may be viewed on a display module or on the Caterpillar Electronic Technician (Cat ET). The current to the IAPCV defaults to 0.0 Amps after 150 milliseconds. The ECM attempts to communicate with the IAPCV at intervals of 120 milliseconds.
- Engine misfires
- Low power
- Reduced engine speed (rpm)
- Engine shutdown
Test Step 1. Perform the following diagnostic procedure: Injection Actuation Pressure Control Valve Circuit - Test
Results:
- OK - STOP
Caterpillar Information System:
3408E and 3412E Engines for Caterpillar Built Machines CID 0042 FMI 05 Injector Actuation Valve open circuit
723PLUS Digital Speed Control Hardware Options
3176C and 3196 Marine Engines Engine Oil Filter Base
2000/01/01 Cooling System Venting Procedure {1350}
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0100 FMI 13 Engine Oil Pressure calibration required
723PLUS Digital Speed Control Control Options
3176C Engine Maintenance Interval Schedule
3114, 3116 and 3126 MUI Engine Governors Throttle Lever (Types IV, V, VI, VII, and Some III) - Remove
3306B Industrial Engine Maintenance Interval Schedule
2000/01/01 New Shafts In Water Pump Groups Provide Increased Torsional Strength {1361, 1389}
3176C Industrial Engine Fan Drive - Install
3176C Industrial Engine Fan Drive - Remove
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
723PLUS Digital Speed Control Software Options
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0110 FMI 04 Engine Coolant Temperature short to ground
3408E and 3412E Engines for Caterpillar Built Machines CID 0164 FMI 03 Injector Actuation Pressure voltage high
2000/01/01 Corrections to Operation and Maintenance Manual, SEBU6759-02 , "Maintenance Interval Schedule" and Corrections to Operation and Maintenance Manual, SEBU6759-02 , "Maintenance Recommendations" {7519}
3408E and 3412E Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0174 FMI 03 Fuel Temperature open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0168 FMI 02 System Voltage intermittent/erratic
3176C and 3196 Engines for Caterpillar Built Machines CID 0168 FMI 01 System Voltage Low
3176C and 3196 Engines for Caterpillar Built Machines CID 0168 FMI 00 System Voltage High
723PLUS Digital Speed Control Accessories
2000/02/01 New Oil Filter Base Group {1306}