Engine Oil Filter Base
Show/hide table
Illustration 1 | g01430933 |
(1) Cover
(2) Oil filter base
(3) Oil filter
(4) Bolts (six total)
Apply 9S-3263 Thread Lock to each of the six bolts.
Show/hide table
Illustration 2 | g01432268 |
Section A-A |
(5) Seal
(6) 8M-3182 Spring
- Assembled length ...
63.5 mm (2.50 inch) - Load at assembled length ...
39.7 N (8.92 lb) - Free length after test ...
91.7 mm (3.61 inch) - Outside diameter ...
20.6 mm (0.81 inch) - Load at assembled length ...
(7) Seal
(8) Plunger
(9) Stud
- Tighten the stud that holds the oil filter to the oil filter base to the following torque. ...
68 ± 7 N·m (50 ± 5 lb ft)
(10) Seal
Show/hide table
Illustration 3 | g01432273 |
Section B-B |
(11) 2N-6005 Spring
- Assembled length ...
96.5 mm (3.80 inch) - Load at assembled length ...
92.5 N (20.80 lb) - Minimum operating length ...
45.7 mm (1.80 inch) - Load at minimum operating length ...
257.6 N (57.91 lb) - Free length after test ...
124.7 mm (4.91 inch) - Outside diameter ...
21.8 mm (0.86 inch) - Load at assembled length ...
(12) Valve
(13) Seal
(14) Seal
Show/hide table
Illustration 4 | g01432277 |
Section C-C |
Relief pressure ...
(15) Spacer
(16) 1A-2170 Spring
- Assembled length ...
21.4 mm (0.84 inch) - Load at assembled length ...
198.0 ± 13.4 N (45 ± 3.5 lb) - Free length after test ...
31.0 mm (1.22 inch) - Outside diameter ...
19.6 mm (0.77 inch) - Load at assembled length ...
(17) Seal
Show/hide table
Illustration 5 | g01432286 |
Section D-D |
(18) 8M-3182 Spring
- Assembled length ...
63.5 mm (2.50 inch) - Load at assembled length ...
39.7 N (8.92 lb) - Free length after test ...
91.7 mm (3.61 inch) - Outside diameter ...
20.6 mm (0.81 inch) - Load at assembled length ...
(19) Plunger
(20) Seal
Caterpillar Information System:
2000/01/01 Cooling System Venting Procedure {1350}
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0100 FMI 13 Engine Oil Pressure calibration required
723PLUS Digital Speed Control Control Options
3176C Engine Maintenance Interval Schedule
3114, 3116 and 3126 MUI Engine Governors Throttle Lever (Types IV, V, VI, VII, and Some III) - Remove
3306B Industrial Engine Maintenance Interval Schedule
2000/01/01 New Shafts In Water Pump Groups Provide Increased Torsional Strength {1361, 1389}
3176C Industrial Engine Fan Drive - Install
3176C Industrial Engine Fan Drive - Remove
3512 Industrial Engine Flywheel
723PLUS Digital Speed Control Application
G3304 and G3306 Engines Test Tools for the Electrical System
723PLUS Digital Speed Control Hardware Options
3408E and 3412E Engines for Caterpillar Built Machines CID 0042 FMI 05 Injector Actuation Valve open circuit
3408E and 3412E Engines for Caterpillar Built Machines CID 0042 FMI 06 Injector Actuation Valve short to ground
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
723PLUS Digital Speed Control Software Options
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0110 FMI 04 Engine Coolant Temperature short to ground
3408E and 3412E Engines for Caterpillar Built Machines CID 0164 FMI 03 Injector Actuation Pressure voltage high
2000/01/01 Corrections to Operation and Maintenance Manual, SEBU6759-02 , "Maintenance Interval Schedule" and Corrections to Operation and Maintenance Manual, SEBU6759-02 , "Maintenance Recommendations" {7519}
3408E and 3412E Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0174 FMI 03 Fuel Temperature open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0168 FMI 02 System Voltage intermittent/erratic
3176C and 3196 Engines for Caterpillar Built Machines CID 0168 FMI 01 System Voltage Low