Tool and Specification Chart for Conventional Duo-Cone Seal Groups {0599, 7561}
- Agricultural Tractor
- All
- Articulated Truck
- All
- Asphalt Paver
- All
- Backhoe Loader
- All
- Challenger
- All
- Cold Planer
- All
- Earthmoving Compactor
- All
- Excavator
- All
- Forest Products
- All
- Integrated Toolcarrier
- All
- Mini Hydraulic Excavator
- All
- Motor Grader
- All
- Off-Highway Truck/Tractor
- All
- Paving Compactor
- All
- Pipelayer
- All
- Road Reclaimer/Soil Stabilizer
- All
- Skid Steer Loader
- All
- Telehandler
- All
- Track-Type Loader
- All
- Track-Type Skidder
- All
- Track-Type Tractor
- All
- Underground Articulated Truck
- All
- Wheel Dozer
- All
- Wheel Loader
- All
- Wheel Skidder
- All
- Wheel Tractor-Scraper
- All
Introduction
Always use an installation tool that is the correct size to install the Duo-Cone Seal. Using the correct sized tool will prevent damage to the toric ring or to the sealing faces of the Duo-Cone Seals.
The installation tool serves two purposes. The tool locates the seal group to the correct distance from a reference surface and the tool positions the seal group around a shaft.
Reference: Special Instruction, SEHS8364, "Assembly and Installation of Conventional Duo-Cone Seals"
Conventional Duo-Cone Seal Tools and Dimensions
Note: Use isopropyl alcohol or other approved lubricants for assembly when you install Duo-Cone Seals.
Show/hide table
Conventional Duo-Cone Seals Tools and Dimensions | |||||||
---|---|---|---|---|---|---|---|
Seal Class | Rubber Toric Cross Section | Example Seal Group | Seal Ring | Installation Tool | Assembled Height | ||
Outside Diameter | Ramp Angle Degrees | Nominal | Tolerance | ||||
B | |
|
15 | |
|
||
|
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
C | |
|
8 | |
|
||
|
20 | |
|||||
|
8 | |
|||||
|
20 | |
|||||
|
20 | |
|||||
|
8 | |
|||||
|
20 | |
|||||
|
8 | |
|||||
C | |
|
20 or 8 | |
|
||
|
20 | |
|||||
|
8 | |
|||||
|
20, 15 or 8 | |
|||||
|
20 | |
|||||
|
20 | |
|||||
D | |
|
15 | |
|
||
|
15 | |
|||||
9G-5313 | |||||||
|
8 | |
|||||
|
15 | |
|||||
|
8 | |
|||||
|
15 | |
|||||
|
8 | |
|||||
D | |
|
15 | |
|
||
|
15 | |
|||||
|
8 | |
|||||
|
15 | |
|||||
D | |
|
15 | |
|
||
|
15 | |
|||||
|
8 | |
|||||
|
20 | |
|||||
|
15 | |
|||||
|
15 | |
|||||
D | |
|
8 | |
|
||
|
15 | |
|||||
|
15 | |
|||||
|
8 | |
|||||
|
15 | |
|||||
|
15 | |
|||||
|
15 | |
|||||
|
15 | |
|||||
|
15 | |
|||||
|
15 | |
|||||
453-5929 | |
16 | |
||||
|
16 | |
|||||
L | |
|
15 | |
|
||
Longwall Miner Application | |
|
|||||
|
16 | |
|
Caterpillar Information System:
G3500 Industrial Engines Electrical Power Supply
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Start/Run/Stop Switch
G3500 Industrial Engines DDT Troubleshooting
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Engine Wiring Harness Diagram
3512B Petroleum Engines Cat Data Link
3512B Petroleum Engines Electronic Control System Operation
320B Excavator Hydraulic System Hydraulic System Pressure - Release
3500B Industrial Engines Permanent Timing Calibration Sensor
G3500 Industrial Engines Inspecting Electrical Connectors
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Ether Injection System
3608 Engine Measuring Engine Oil Pressure
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Overspeed Verify Switch
3524B Engines for Off-Highway Trucks Analog Sensor - Calibrate
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Engine Speed/Timing Sensor - Calibrate
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Air Shutoff System
3176C and 3196 Engines for Caterpillar Built Machines Belt Tensioner - Remove and Install
G3500B Engines Fuel System Operation
G3500B Engines Electronic Control Module (ECM) - 16 Cylinders
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader Electrical Connectors - Inspect
G3500 Engines Reference Material
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0279 - FMI 03 Aftercooler Temperature open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0279 - FMI 04 Aftercooler Temperature short to ground
3500B and 3500B High Displacement Generator Set Engines Engine Monitoring System