Pistons and Connecting Rods - Assemble
组装步骤
Show/hide table
需要的工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 4C-3601     | 活塞环扩张器     | 1     |
B     | 1P-1861     | 挡圈钳     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
验证活塞和连杆是否正确组装。 确保连杆和连杆盖上刻的号码处在正确的位置。 连杆和连杆盖的标号对应应该安装的气缸。 |
- 检查活塞环 (5) 端隙。 请参阅技术参数, "活塞和活塞环"。
Show/hide table
图 1 | g01139074 |
Show/hide table
图 2 | g01139072 |
注: 此发动机配备裂解式连杆。 必须小心处理裂解式连杆。 使用软口台钳,固定连杆盖螺栓。
- 使用工具 (A) ,安装控油活塞环。 应从活塞环端隙转动弹簧两侧 180 度。
- 安装中间活塞环,"UP-2" 标记的一侧朝向活塞顶部。 使用工具 (A) ,安装活塞环。
- 安装顶活塞环,"UP-1" 标记的一侧朝向活塞顶部。 使用工具 (A) ,安装活塞环。
- 检查活塞头 (6) 中的轴承 (7) 。 如果活塞冠部磨损或损坏的话,必须进行更换。
- 在连杆 (1) 上定位活塞裙 (2) 和活塞头 (6) 。 将清洁的发动机机油涂抹在活塞销 (4) 上,然后安装活塞销 (4). 使用工具 (B) ,安装挡圈 (3) 。 确保挡圈 (3) 位于活塞裙部 (2) 的槽中。
End By: 安装活塞和连杆。 请参阅 解体和组装, "活塞和连杆 - 安装"。
Caterpillar Information System:
C9 Engines for Caterpillar Built Machines Cylinder Liner - Install
C-9 Engines for Caterpillar Built Machines Cylinder Liner Projection
Customer Communication Module (CCM) for Diesel Engines General Wiring Diagram
3612 and 3616 Engines Electric Starting Motor - Remove and Install
C9 On-highway Engines Engine Operation
C9 On-highway Engines Diagnostic Lamp
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines AL Fault Code - Troubleshoot
C9 On-highway Engines Monitoring System
Installation Of Double Wall Fuel Lines For 3412C High Performance Marine Engines{1252} Installation Of Double Wall Fuel Lines For 3412C High Performance Marine Engines{1252}
Uninterruptible Power Supply (UPS) 250 Symbols
Uninterruptible Power Supply (UPS) 250 Electrical System
Uninterruptible Power Supply (UPS) 250 General Hazard Information
Customer Communication Module (CCM) for Diesel Engines Data Link Guidelines
3618 Engine Engine Oil Level Switch - Remove and Install
3406E and 3456 Engines for Caterpillar Built Machines Troubleshooting
C-9 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
3054B Industrial Engine Gear Group (Front) - Remove
3054B Industrial Engine Gear Group (Front) - Install
3126B Engine for Caterpillar Built Machines Engine Will Not Crank
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders MID 036 - CID 0277 - FMI 08 Timing Calibration signal abnormal
30SI Series and 34SI Series Alternator T1 Alternator Output - Test
30SI Series and 34SI Series Alternator T2 Electrical System Current - Test
3406E and 3456 Generator Set Engines Fuel Quality - Test
30SI Series and 34SI Series Alternator T3 Charging System - Test