Engine Oil Filter Base - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 185-3630 | 带式扳手组件 | 1 |
Show/hide table
 |
热油和热的部件可能会导致人身伤害。 不要让热油或热的部件与皮肤接触。 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品，参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 用工具 (A) 将机油滤清器 (2) 从机油滤清器底座 (3) 上拆下。
Show/hide table
 | |
| 图 1 | g00813775 |
Show/hide table
 | |
| 图 2 | g00813789 |
- 将螺栓 (1) 和垫圈从机油滤清器底座 (3) 上拆下。
- 将机油滤清器底座 (3) 从发动机上拆下。
- 检查 O 形密封圈 (4) 的状态。 更换磨损或损坏的 O 形密封圈。
- 必要时，通过拆下八条螺栓 (6) 和垫圈将板 (5) 从发动机上拆下。
Show/hide table
 | |
| 图 3 | g00813823 |
- 检查密封垫（未显示）的状态。 更换磨损或损坏的密封垫。
- 检查机油滤清器底座 (3) 和板 (5) 有无堵塞和裂纹。 利用备件更换损坏的部件。
Caterpillar Information System:
302.5 Mini Hydraulic Excavator Hydraulic System Control Valve (Straight Travel)
302.5 Mini Hydraulic Excavator Hydraulic System Combined Function Hydraulic Operation
3056 Engine for Caterpillar Built Machines Fuel Injection Lines - Remove
3064 and 3066 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
W330B Material Handler Hydraulic System Pump Hydraulic System
365B and 365B Series II Excavators Supplement for 3196 Engine Refrigerant Compressor - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
Pin Grabber Quick Coupler Quick Coupler - Lubricate
5230 Excavator Machine Parking
5230 Excavator Machine Operation
W330B Material Handler Hydraulic System Pilot Hydraulic System
3064 and 3066 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
365B and 365B Series II Excavators Supplement for 3196 Engine Refrigerant Accumulator - Remove and Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0190 - FMI 02 Loss of Engine Speed signal
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0190 - FMI 03 Engine Speed open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0190 - FMI 08 Engine Speed signal abnormal
W330B Material Handler Hydraulic System General Information
Commissioning Procedure For The Hydraulic Generator{1404, 5050} Commissioning Procedure For The Hydraulic Generator{1404, 5050}
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Main Hydraulic Pump Air Pressure - Purge
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Solenoid Valve (Two Speed Travel) - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Solenoid Valve (Proportional Reducing) - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Relief Valve (Pilot) - Remove and Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Ether Starting Aid
3064 and 3066 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install