3500B Engines Caterpillar

Accessory Drive (Lower Left Hand, Reverse Rotation)

Usage:

3508B 1TW

Show/hide table




Illustration 1	g00279994

(1) Bearing

Bore in the bearings after assembly ... 75.000 ± 0.055 mm (2.9528 ± 0.0022 inch)

(2) Thrust washer

Thickness of new thrust washer ... 8.50 ± 0.05 mm (0.335 ± 0.002 inch)

(3) Shaft

Diameter of new shaft ... 74.900 ± 0.015 mm (2.9488 ± 0.0006 inch)

Width of groove in new shaft for the thrust washer ... 8.750 ± 0.025 mm (0.3445 ± 0.0010 inch)

End play for shaft ... 0.175 to 0.325 mm (0.0069 to 0.0128 inch)

(4) Spacer

(5) Bearing

Bore in the bearings after assembly ... 75.000 ± 0.055 mm (2.9528 ± 0.0022 inch)

Caterpillar Information System:

3500B Engines Accessory Drive (Upper Left Hand, Reverse Rotation)

3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Lifter Group - Remove and Install

Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 168 FMI 3 Electrical System Voltage Above Normal - Test

797 Off-Highway Truck Air System Air Horn

Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 111 FMI 3 Fluid Level Sensor (Engine Coolant) Voltage Above Normal - Test

3406E and 3456 Generator Set Engines Gear Group (Front) - Install

3126B Marine Engine Cylinder Block Cover Group

Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 110 FMI 4 Temperature Sensor (Engine Coolant) Voltage Below Normal - Test

3408E and 3412E Engines for Caterpillar Built Machines Increased Engine Oil Temperature - Inspect

C-10 and C-12 Industrial Engines Excessive Engine Oil Consumption - Inspect

3408E and 3412E Engines for Caterpillar Built Machines Excessive Bearing Wear - Inspect

3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install

3126B Marine Engine Crankshaft Seals

3406E and 3456 Generator Set Engines Electric Starting Motor - Remove and Install

3500B Engines Air Cleaner - Remove and Install

3500B Engines and 3500 Engines with EUI Option Speed Control

Installation Instructions for the Accessory Module Support{7060} Installation Instructions for the Accessory Module Support{7060}

Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 168 FMI 4 Electrical System Voltage Below Normal - Test

Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test

3126B Marine Engine Vibration Damper

3114, 3116, and 3126 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install

Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test

3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install

Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test