Lifter Group - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1U-7262 | Telescoping Magnet | 1 |
Start By:
- Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to remove lifter (1) from the cylinder block.
Note: Mark the original location of the lifters for later installation.
Show/hide table
 | |
| Illustration 1 | g00828101 |
- Inspect lifter (1) for wear or damage. If the lifters are worn or damaged, use new parts for replacement.
- Repeat Steps 1 and 2 for the remaining lifters.
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that lifter (1) is clean and that the oil hole in the lifter is not restricted. Lubricate the lifter with clean engine oil and install the lifter in the cylinder block.
Show/hide table
 | |
| Illustration 2 | g00692979 |
- Repeat Step 1 for the remaining lifters.
Note: Ensure that the lifters are installed in the original location.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 168 FMI 3 Electrical System Voltage Above Normal - Test
797 Off-Highway Truck Air System Air Horn
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 111 FMI 3 Fluid Level Sensor (Engine Coolant) Voltage Above Normal - Test
3406E and 3456 Generator Set Engines Gear Group (Front) - Install
3126B Marine Engine Cylinder Block Cover Group
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 110 FMI 4 Temperature Sensor (Engine Coolant) Voltage Below Normal - Test
3408E and 3412E Engines for Caterpillar Built Machines Increased Engine Oil Temperature - Inspect
C-10 and C-12 Industrial Engines Excessive Engine Oil Consumption - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Excessive Bearing Wear - Inspect
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Charging System - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 110 FMI 3 Temperature Sensor (Engine Coolant) Voltage Above Normal - Test
3500B Engines Accessory Drive (Upper Left Hand, Reverse Rotation)
3500B Engines Accessory Drive (Lower Left Hand, Reverse Rotation)
3126B Marine Engine Crankshaft Seals
3406E and 3456 Generator Set Engines Electric Starting Motor - Remove and Install
3500B Engines Air Cleaner - Remove and Install
3500B Engines and 3500 Engines with EUI Option Speed Control
Installation Instructions for the Accessory Module Support{7060} Installation Instructions for the Accessory Module Support{7060}
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 168 FMI 4 Electrical System Voltage Below Normal - Test
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
3126B Marine Engine Vibration Damper
3114, 3116, and 3126 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test