Accessory Drive (Upper Left Hand, Reverse Rotation)
Show/hide table
 | |
| 图 1 | g01371445 |
(2) 附件驱动齿轮 (5) 止推垫圈 (6) 惰轮 | |
(1) 组装后的套筒轴承孔孔径 ... 75.000 ± 0.055 mm (2.9528 ± 0.0022 in)
(3) 新止推垫圈的厚度 ... 8.50 ± 0.05 mm (0.335 ± 0.002 in)
(4) 辅助驱动轴
- 新辅助驱动轴直径 ... 74.900 ± 0.015 mm (2.9488 ± 0.0006 in)
- 新辅助驱动轴的槽宽度 ... 8.750 ± 0.025 mm (0.3445 ± 0.0010 in)
- 附助驱动轴轴向间隙 ... 0.175 到 0.325 mm (0.0069 到 0.0128 in)
- 新辅助驱动轴的槽宽度 ... 8.750 ± 0.025 mm (0.3445 ± 0.0010 in)
(7) 套筒轴承
- 组装后套筒轴承孔孔径 ... 90.000 ± 0.010 mm (3.5433 ± 0.0004 in)
- 最大粗糙度平均值 （Ra） ... 0.8 微米 (32 微英寸)
注: 将套筒轴承装至齿轮内后必须将套筒轴承加工至规定尺寸。
(8) 新轴直径 ... 89.880 ± 0.020 mm (3.5386 ± 0.0008 in)
Caterpillar Information System:
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 168 FMI 3 Electrical System Voltage Above Normal - Test
797 Off-Highway Truck Air System Air Horn
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 111 FMI 3 Fluid Level Sensor (Engine Coolant) Voltage Above Normal - Test
3406E and 3456 Generator Set Engines Gear Group (Front) - Install
3126B Marine Engine Cylinder Block Cover Group
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 110 FMI 4 Temperature Sensor (Engine Coolant) Voltage Below Normal - Test
3408E and 3412E Engines for Caterpillar Built Machines Increased Engine Oil Temperature - Inspect
C-10 and C-12 Industrial Engines Excessive Engine Oil Consumption - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Excessive Bearing Wear - Inspect
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Charging System - Test
3500B Engines Accessory Drive (Lower Left Hand, Reverse Rotation)
3126B Marine Engine Crankshaft Seals
3406E and 3456 Generator Set Engines Electric Starting Motor - Remove and Install
3500B Engines Air Cleaner - Remove and Install
3500B Engines and 3500 Engines with EUI Option Speed Control
Installation Instructions for the Accessory Module Support{7060} Installation Instructions for the Accessory Module Support{7060}
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 168 FMI 4 Electrical System Voltage Below Normal - Test
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
3126B Marine Engine Vibration Damper
3114, 3116, and 3126 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install