Crankshaft Rear Seal - Install
Show/hide table
带后齿轮系发动机所需的工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 5P-7301 | 定位工具 | 1 |
5P-7309 | 螺栓 | 2 | |
5P-7310 | 螺栓 | 2 | |
8T-2683 | 油封安装工具 | 1 | |
9S-8858 | 螺母 | 1 | |
不带后齿轮系发动机所需的工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
B | 5P-1733 | 定位工具 | 1 |
5P-1737 | 螺栓 | 3 | |
6V-6143 | 油封安装工具 | 1 | |
9S-8858 | 螺母 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 一旦密封圈与承磨衬套分开,不得再次使用这些部件。 维修密封前,请参阅 专门说明书, SMHS8508, "密封唇内具有液力槽的曲轴密封总成的特别处理信息和安装说明 "。
注: 在安装曲轴密封和承磨衬套的过程中,请勿使用任何类型的润滑剂。
注: 在安装承磨衬套前,检查曲轴有无划伤,或者曲轴表面有无任何可能导致失圆状态的变形。 使用抛光布清除曲轴上的缺陷。
- 利用工具 (A) 或工具 ( B)、采用以下方式安装曲轴后密封 ( 6) 和承磨衬套 (1):
- 使用 169-5464 快速固化底漆 清洁曲轴 (3) 外周以及承磨衬套 ( 1) 的内周。
- 将 4C-9507 锁固胶 涂覆在曲轴 (3) 的外周。 将 4C-9507 锁固胶涂抹在承磨衬套 ( 1) 的内周。
- 将定位工具 (2) 定位到曲轴 ( 3) 上。 安装将定位工具固定到曲轴上的螺栓 ( 7)。
Show/hide table
图 3 g00565570 典型实例 - 将承磨衬套 (1) 和密封 ( 6) 安装到曲轴 (3) 上。 将安装工具 (4) 放到定位工具 ( 2) 上。
Show/hide table
图 4 g00565576 典型实例 - 润滑螺母 (5) 的表面。 将螺母 (5) 安装到定位工具 ( 4) 上。
- 上紧螺母 (5),直到安装工具 ( 4) 接触定位工具 (2)。
- 拆下工具 (A) 或 ( B) 后检查曲轴油封和承磨衬套是否安装正确。
Show/hide table图 2 g00582512 典型实例
Show/hide table
图 1 | g00477681 |
结束:
- 安装飞轮。 请参阅 拆解和组装, "飞轮 - 安装" 。
Caterpillar Information System:
3500 and 3500B Engines Cooling System Coolant (DEAC) - Change
3034 Engine for Caterpillar Built Machines Engine Oil Pan - Remove and Install
G3500 Engines Piston and Connecting Rods - Remove
3612 and 3616 Engines Engine Oil Cooler
3034 Engine for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
3524B Engine for Caterpillar Built Machines Connecting Rod Bearings - Remove and Install
EMCPII+ for Gas Engines Speed Sensor (Engine) - Adjust
EMCPII+ for Gas Engines EMCP Electronic Control (Generator Set) - Replace
EMCPII+ for Gas Engines EMCP Electronic Control (AC Transformer Box) - Replace
EMCPII+ for Gas Engines Relay Module - Replace
EMCPII+ for Gas Engines Alarm Module Control - Adjust
EMCPII+ for Gas Engines AC Voltage Range - Adjust
3116 Truck Engine Engine Storage
3176B Marine Engine Maintenance Interval Schedule
3116 Truck Engine Gauges and Indicators
Electronic Modular Control Panel II+ (EMCP II+) Starting Motor Magnetic Switch - Test - 3306B and 3406C MUI Engines
3500 and 3500B Engines Cooling System Coolant (ELC) - Change
3500B High Displacement Generator Set Engines Engine Oil and Filter - Change
3126B Marine Engine Fuel System
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Lines
3034 Engine for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
3500 and 3500B Engines Walk-Around Inspection - Exercise Inspection of Standby Generator Set Engines
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Valve Rocker Arms and Lifters
G3500 Engines Piston and Connecting Rods - Install