Connecting Rod Bearings - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 448-5087 | 盘车工具 (1) | 1 |
Show/hide table
(1) | 9S-9082 发动机盘车工具是备用工具。 |
开始步骤:
a. 拆下活塞冷却喷嘴。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (A) 转动飞轮,以便可以接近要拆卸的连杆盖。
Show/hide table
图 1 g01064418 注: 检查连杆和连杆盖上的识别标记是否正确。 连杆和连杆盖侧面应该有蚀刻的编号。 该编号必须与气缸号一致。 如有必要,标记连杆和连杆盖。
- 从曲轴上拆卸螺栓 (1) 和连杆盖 (2)。
- 将连杆从曲轴内推出并拆卸连杆轴承的上半部分。
Show/hide table
图 2 g01064420 - 从连杆盖 (2) 上拆卸连杆轴承的下半部分 (3)。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | - | Bel-Ray 二硫化钼润滑油 67700 (1) | - |
Show/hide table
(1) | 参考下方链接,以定购上方规定的二硫化钼润滑油 - www.belray.com |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 检查轴承间隙。 有关正确步骤,请参阅拆解和组装, "轴承间隙 - 检查"。
- 将清洁的发动机机油涂在连杆轴承上。
Show/hide table
图 3 g01064420 - 在连杆盖 (2) 中安装连杆轴承的下半部分 (3)。 确保轴承后面的凸台在连杆盖上的轴承凸台凹槽内。
- 在连杆内安装连杆轴承的上半部分。 确保轴承后面的凸台在连杆的轴承凸台凹槽内。
- 在曲轴上安装连杆。
Show/hide table
图 4 g01064418 - 将连杆盖 (2) 安置在连杆上。 确保连杆盖 (2) 一侧的编号与连杆编号对应。
- 将工具 (B) 涂抹在螺栓 (1) 的螺纹、螺杆和底座上。 安装螺栓 (1)。
- 将螺栓 (X1) 和 (X3) 拧紧至
90 ± 5 N·m (65 ± 4 lb ft) . - 将螺栓 (X2) 和 (X4) 拧紧至
90 ± 5 N·m (65 ± 4 lb ft) . - 将螺栓 (X2) 和 (X4) 再次拧紧至
90 ± 5 N·m (65 ± 4 lb ft) . - 在转至最终扭矩前,涂画或标记螺栓盖及连杆。
- 将所有螺栓再拧紧 90 ± 5 度 (1/4圈)。
Show/hide table图 5 g06117798 (4) 带斜面的连杆侧
(5) 定位销注: 涂画或标记螺栓头及连杆,以确保再旋转 90 度后的最终角度正确。
- 将螺栓 (X1) 和 (X3) 拧紧至
- 检查同一轴径上的两个连杆间是否存在侧隙。 间隙必须为
0.85 ± 0.332 mm (0.034 ± 0.0130 inch) 。
结束步骤:
a. 安装活塞冷却喷嘴。
Caterpillar Information System:
EMCPII+ for Gas Engines Speed Sensor (Engine) - Adjust
EMCPII+ for Gas Engines EMCP Electronic Control (Generator Set) - Replace
EMCPII+ for Gas Engines EMCP Electronic Control (AC Transformer Box) - Replace
EMCPII+ for Gas Engines Relay Module - Replace
EMCPII+ for Gas Engines Alarm Module Control - Adjust
EMCPII+ for Gas Engines AC Voltage Range - Adjust
EMCPII+ for Gas Engines External Potential Transformer Connections
Electronic Modular Control Panel II+ (EMCP II+) Electrical Connector - Inspect
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Track Adjuster
3116 Truck Engine Engine Description
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Track Roller Mounting
3116 Truck Engine Model View Illustrations
3034 Engine for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
3612 and 3616 Engines Engine Oil Cooler
G3500 Engines Piston and Connecting Rods - Remove
3034 Engine for Caterpillar Built Machines Engine Oil Pan - Remove and Install
3500 and 3500B Engines Cooling System Coolant (DEAC) - Change
3408E and 3412E Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
3116 Truck Engine Engine Storage
3176B Marine Engine Maintenance Interval Schedule
3116 Truck Engine Gauges and Indicators
Electronic Modular Control Panel II+ (EMCP II+) Starting Motor Magnetic Switch - Test - 3306B and 3406C MUI Engines
3500 and 3500B Engines Cooling System Coolant (ELC) - Change
3500B High Displacement Generator Set Engines Engine Oil and Filter - Change