Auxiliary Water Pump - Disassemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-1859 | Pliers | 1 |
B | 5F-7465 | Puller | 1 |
1P-7461 | Legs | 2 | |
5P-4750 | Screw | 1 | |
1P-0510 | Driver Gp | 1 | |
C | 1P-1861 | Pliers | 1 |
D | 9S-9152 | Bearing Puller | 1 |
E | 1P-0510 | Driver Gp | 1 |
E | 1P-0510 | Driver Gp | 1 |
F | 8S-6470 | Forcing Screw | 1 |
Start By:
- Remove the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (1) and cover (2) from housing (3).
Show/hide table
Illustration 2 g00558497 - Use Tooling (F) to remove impeller (4) and plate (5) from housing (3).
Show/hide table
Illustration 3 g01102409 - Use Tooling (A) to remove retaining ring (6). Remove seal assembly (7) from housing (3).
Show/hide table
Illustration 4 g00578760 Show/hide tableIllustration 5 g01102364 - Remove the ceramic part of seal assembly (7) when the shaft assembly is removed from the housing. Use Tooling (E) and a suitable press to remove the seal from housing (3).
Show/hide table
Illustration 6 g01102410 - Remove bolts (8) and housing (3) from body (9).
- Remove bolt (10).
- Use Tooling (B) to remove gear (11) from the shaft assembly.
Show/hide table
Illustration 7 g00558575 - Use Tooling (C) to remove retaining ring (12). Remove the shaft assembly from the body.
Show/hide table
Illustration 8 g00558606 Show/hide tableIllustration 9 g00558609 - Use Tooling (D) and a suitable press to remove bearing (13) from shaft (14).
- Remove spacer (15).
- Use Tooling (D) and a suitable press to remove bearing (17) from shaft (14).
- Use Tooling (A) to remove retaining ring (16).
Show/hide table
Illustration 10 g00578776 - Use Tooling (E) and a suitable press to remove seal (18) from body (9).
Show/hide table
Illustration 1 | g00558403 |
Caterpillar Information System:
3412E, C30 and C32 Marine Engines Auxiliary Water Pump - Install
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers High Speed Coupling for Gearbox
3412E, C30 and C32 Marine Engines Auxiliary Water Pump - Remove
Caterpillar PRELUB® Diagnostics{1469} Caterpillar PRELUB® Diagnostics{1469}
3408E and 3412E Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Joint Assembly for Water Line
G3408 and G3412 Engines Governor and Magneto Drive
3406E and 3456 Generator Set Engines Flywheel - Install
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers General Information
3054 and 3056 Industrial and Generator Set Engines Lubrication System
G3408 and G3412 Engines Turbocharger
Procedure for Replacing the Software for the Electronic Ignition System (EIS){1902} Procedure for Replacing the Software for the Electronic Ignition System (EIS){1902}
3412E and C30 Marine Engines Serial Number Plate
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers High Speed Coupling for Gearbox
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Heat Exchanger
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Control Panel (AC Power)
Control Console For CPS361 Pumper, Cement Battery Disconnect
G3606 and G3608 Engines Crankshaft Front Seal and Wear Sleeve - Remove
G3606 and G3608 Engines Crankshaft Front Seal and Wear Sleeve - Install
Control Console For CPS361 Pumper, Cement Engine Electronics
3406C (PEEC III) Truck Engines Compression Brake
3412E, C30 and C32 Marine Engines Auxiliary Water Pump - Assemble
G3408 and G3412 Engines Auxiliary Water Pump
G3606 and G3608 Engines Crankshaft Rear Seal - Remove