Aftercooler - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     |     | 3/8 英寸导螺栓     | 2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g00922785 |
- 将新密封件 (3) 安装在后冷器芯上。
注: 请勿将任何密封胶或粘合剂涂在密封件 (3) 上。
- 安装工具 (A) 。 将垫片 (4) 安装在每个导螺栓上。
- 将起重机固定至后冷器芯上。 将后冷器芯安装至后冷器壳体中。 卸下导螺栓。 将两个螺钉安装至导螺栓的先前位置。 拧紧螺钉至扭矩 30 ± 7 N·m (22 ± 5 lb ft)。
End By: 安装后冷器。 请参阅 拆解和组装, "后冷器 - 安装"。
Caterpillar Information System:
G3606 and G3608 Engines Aftercooler - Disassemble
3054 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
3612 and 3616 Fast Vessel Engines Warranty Information
3054 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Install
3600 Heavy Fuel Engines Engine Protection Devices - Calibrate
3054 Truck Engine Crankshaft Rear Seal - Remove
3126 Truck Engine (Military) Extended Life Coolant (ELC) Cooling System Maintenance
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Install
3126 Truck Engine (Military) Extended Life Coolant (ELC)
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove
G3408 and G3412 Engines Engine Design
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Glossary of Terms
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Initial Troubleshooting Procedure
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System System Schematic
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System System Self Test
3412E, C30 and C32 Marine Engines Turbocharger - Install
G3408 and G3412 Engines Exhaust Manifold
3408E and 3412E Engines for Caterpillar Built Machines Hydraulic Pump Drive
3054 Truck Engine Exhaust Manifold - Remove and Install
G3606 and G3608 Engines Actuator (Heinzman) - Remove and Install
3054 Engine for Caterpillar Built Machines Fan - Remove and Install
3606 and 3608 Engines Pressure Switch
G3606 and G3608 Engines Turbocharger - Remove