G3500 Engines Caterpillar

Camshaft

Usage:

G3516 4EK

Show/hide table




Illustration 1	g03124339
(1) Left-hand camshaft assembly (2) Right-hand camshaft assembly

Show/hide table

Table 1
Specification for 4P-8352 Camshaft Gp
Item	Qty	Part	Specification Description
A	-	-	Thickness of the groove in a new camshaft assembly is 8.75 ± 0.05 mm (0.344 ± 0.002 inch).
C	1	5B-5821 Dowel	Extension of the dowel is 12.0 ± 0.5 mm (0.47 ± 0.02 inch).
D	2	4N-1650 Dowel	Extension of the dowel is 22.0 ± 0.5 mm (0.87 ± 0.02 inch).
E	2	7N-3218 Thrust Washer	Thickness of a new thrust washer is 8.50 ± 0.05 mm (0.335 ± 0.002 inch).
F	-	-	Diameter of bearing journals in a new journal camshaft assembly is 85.88 ± 0.02 mm (3.381 ± 0.001 inch).
F	-	-	Bore in camshaft bearing after installation is 86.00 ± 0.06 mm (3.386 ± 0.002 inch).
-	-	-	End play for a new camshaft assembly is 0.15 to 0.35 mm (0.006 to 0.014 inch).
3	16	5P-0076 Bolt	Torque to 55 ± 7 N·m (41 ± 5 lb ft).

Show/hide table




Illustration 2	g03125836

Show/hide table

Table 2
Item	Qty	Part	Specification Description
-	-	-	Use the following procedure in order to determine the camshaft lobe lift:
			1. Measure camshaft lobe height (H).
			2. Measure base circle (J).
			3. Subtract the base circle (J) from the camshaft lobe height (H). The difference is the actual camshaft lobe lift.
G	-	-	Specified camshaft lobe lift:
			Inlet lobe is 9.201 mm (0.3622 inch).
			Exhaust lobe is 8.699 mm (0.3425 inch).

Caterpillar Information System:

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Engine Oil in Cooling System

G3300 Engines Ignition System Spark Plugs - Inspect/Replace

318B Excavator Machine System Specifications Track Roller (Single Flange)

3500 Spark Ignited Engines Engine Design

3406E On-Highway Engine Engine Oil Pressure Sensor - Remove and Install

3406E On-Highway Engine Coolant Temperature Sensor - Remove and Install

3406C (PEEC III) Truck Engines Glossary of Electronic Control Terms

3406E Engine Speed/Timing Sensor - Remove and Install

3176C Engine Cooling System Coolant (DEAC) - Change

G3300 Engines Engine Air Cleaner Service Indicator - Inspect

3406E and 3456 Generator Set Engines Fan Drive - Install

3406E On-Highway Engine Fan Drive - Remove

C-10 and C-12 Truck Engines Compression Brake

G3300 Engines Cooling System Coolant (DEAC) - Change

3176C and 3196 Industrial Engines Engine Oil Pressure Sensor - Remove and Install

3176C and 3196 Industrial Engines Speed/Timing Sensor - Remove and Install

3524B Engines for Off-Highway Trucks Fuel in Cooling System

3176C Engine Cooling System Coolant (ELC) - Change

3500B and 3500B High Displacement Generator Set Engines Oil Contains Coolant

3516B Engine for Caterpillar Built Machines Engine Has Early Wear

3524B Engines for Off-Highway Trucks Low Engine Oil Pressure

3606 and 3608 Engines Exhaust Manifold

3524B Engines for Off-Highway Trucks Coolant Temperature Is Too High

3516B Engine for Caterpillar Built Machines Fuel Dilution of Engine Oil