Rear Power Take-Off (RPTO) - Remove and Install
Removal Procedure
Start By:
- Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" .
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove gear assembly (1) .
Show/hide table
 | |
| Illustration 1 | g00484197 |
- Remove bronze thrust washer (2) .
Show/hide table
 | |
| Illustration 2 | g00484198 |
- Remove two dowel pins (3) . Remove bearing sleeve (4) .
Show/hide table
 | |
| Illustration 3 | g00484199 |
- Remove bronze thrust washer (5) from the flywheel housing. Remove two dowel pins (6) .
Show/hide table
 | |
| Illustration 4 | g00484242 |
- Remove seat (7) and bearing sleeve (8) from the flywheel housing.
Show/hide table
 | |
| Illustration 5 | g00484341 |
- Remove two bolts (11) , shaft (10) and the two O-rings. Remove idler gear (9) . Remove the bearing from idler gear (9) .
Show/hide table
 | |
| Illustration 6 | g00484342 |
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1P-0510 | Driver Group | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Check the condition of the O-ring seals. If the O-ring seals are worn or damaged, use new parts for replacement.
- Use Tool (A) and install the bearing in idler gear (9) . The bearing must not project beyond either face.
Show/hide table
| | |
| Illustration 7 | g00484342 |
- Install the two O-ring seals, shaft (10) , idler gear (9) and two bolts (11) . Apply 5P-3413 Pipe Sealant to the threads of the two bolts (11) prior to installation. Tighten two bolts (11) to a torque of 135 ± 15 N·m (100 ± 11 lb ft) .
- Use Tool (A) and install bearing sleeve (8) and seal (7) in the flywheel housing.
Show/hide table
| | |
| Illustration 8 | g00484341 |
- Install two dowel pins (6) . Install bronze thrust washer (5) in the flywheel housing.
Show/hide table
| | |
| Illustration 9 | g00484242 |
- Coat bearing sleeve (4) with clean engine oil. Use Tool (A) and install bearing sleeve (4) . Install two dowel pins (3) .
Show/hide table
| | |
| Illustration 10 | g00484199 |
- Install bronze thrust washer (2) .
Show/hide table
| | |
| Illustration 11 | g00484198 |
- Install gear assembly (1) .
Show/hide table
| | |
| Illustration 12 | g00484197 |
End By: Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Caterpillar Information System:
G3606 and G3608 Engines Basic Block
3176C and 3196 Industrial Engines Cylinder Head
3406E, C-10, C-12, C-15, C-16 Truck Engines Fuel System - Prime
3406E, C-10 and C-12 Truck Engines Electronic Unit Injector - Inspect/Adjust
C-10 and C-12 Truck Engines Air Inlet and Exhaust System
Electronic Modular Control Panel II (EMCP II) for EUI Engines EMCP Electronic Control (Generator Set)
Electronic Modular Control Panel II (EMCP II) for EUI Engines Component Location
G3606 and G3608 Engines Lubrication System
G3612 and G3616 Engines Air Starting System
3176C and 3196 Engines for Caterpillar Built Machines Engine Oil Filter Base
3306C Truck Engine Crankshaft - Install
3306C Truck Engine Crankshaft - Remove
3306C Truck Engine Front Housing - Remove
3306C Truck Engine Front Housing - Install
Electronic Modular Control Panel II (EMCP II) for EUI Engines Instrument Panel
3304B and 3306B Engines for Caterpillar Built Machines Automatic Timing Advance - Remove
C-10 and C-12 Truck Engines Engine Design
C-10 and C-12 Truck Engines Glossary of Electronic Control Terms
C-10 and C-12 Truck Engines Electronic Control System
Electronic Modular Control Panel II (EMCP II) for EUI Engines Electrical Converter (Pulse Width Modulated)
Electronic Modular Control Panel II (EMCP II) for EUI Engines Sensors
Electronic Modular Control Panel II (EMCP II) for EUI Engines Electronic Control Module (Engine)
Electronic Modular Control Panel II (EMCP II) for EUI Engines Modes Of Operation
Electronic Modular Control Panel II (EMCP II) for EUI Engines Normal Mode