Front Housing - Install
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install new gasket (1) on the timing gear plate. Cut the gasket even with the bottom face on the cylinder block.
Note: Check the condition of the gaskets and the O-ring seals. If the gaskets or the O-ring seals are damaged or worn, use new parts for replacement.
Show/hide table
Illustration 1 | g00474497 |
- Install timing gear cover (2) .
- Tighten bolts (3) and (4) to a torque of 23 ± 4 N·m (17 ± 3 lb ft) .
Show/hide table
Illustration 2 | g00474498 |
- Use four bolts (5) , the nuts and the washers in order to install alternator bracket (6) . Use four bolts (7) and install bracket (8) .
Show/hide table
Illustration 3 | g00474501 |
- Ensure that O-ring seal (9) is in position on trunnion (10) . Install trunnion (10) and six bolts. Tighten the bolts to a torque of 135 ± 20 N·m (100 ± 15 lb ft) .
Show/hide table
Illustration 4 | g00474502 |
- Use two bolts and install the O-ring seal and cover (11) . Tighten the bolts to a torque of 100 ± 10 N·m (74 ± 7 lb ft) .
Show/hide table
Illustration 5 | g00474503 |
End By:
- Install the crankshaft front seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Install" .
- Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install" .
- Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install" .
- Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" .
Caterpillar Information System:
3306C Truck Engine Front Housing - Remove
3306C Truck Engine Rear Power Take-Off (RPTO) - Remove and Install
G3606 and G3608 Engines Basic Block
3176C and 3196 Industrial Engines Cylinder Head
3406E, C-10, C-12, C-15, C-16 Truck Engines Fuel System - Prime
3406E, C-10 and C-12 Truck Engines Electronic Unit Injector - Inspect/Adjust
C-10 and C-12 Truck Engines Air Inlet and Exhaust System
Electronic Modular Control Panel II (EMCP II) for EUI Engines EMCP Electronic Control (Generator Set)
Electronic Modular Control Panel II (EMCP II) for EUI Engines Component Location
G3606 and G3608 Engines Lubrication System
G3612 and G3616 Engines Air Starting System
3176C and 3196 Engines for Caterpillar Built Machines Engine Oil Filter Base
Electronic Modular Control Panel II (EMCP II) for EUI Engines Instrument Panel
3304B and 3306B Engines for Caterpillar Built Machines Automatic Timing Advance - Remove
C-10 and C-12 Truck Engines Engine Design
C-10 and C-12 Truck Engines Glossary of Electronic Control Terms
C-10 and C-12 Truck Engines Electronic Control System
Electronic Modular Control Panel II (EMCP II) for EUI Engines Electrical Converter (Pulse Width Modulated)
Electronic Modular Control Panel II (EMCP II) for EUI Engines Sensors
Electronic Modular Control Panel II (EMCP II) for EUI Engines Electronic Control Module (Engine)
Electronic Modular Control Panel II (EMCP II) for EUI Engines Modes Of Operation
Electronic Modular Control Panel II (EMCP II) for EUI Engines Normal Mode
P16, P20, P25, P28, P40 and P60 Pulverizer Crusher Tooth and Cutting Edge Bolts - Tighten
G3606 and G3608 Engines Engine Design