Final Drive Planetary (Drum Propel) - Disassemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 126-6608 | Spanner Socket | 1 |
Start By:
- Remove the final drive planetary. Refer to Disassembly and Assembly, "Final Drive Planetary (Drum Propel) - Remove".
- Remove bolts (9). Remove cover (1) and O-ring seal (7) from housing (8).
- Remove thrust washer (2), sun gear (3), and bearing thrust washer (4) from carrier assembly (5). Thrust washer (2) and bearing thrust washer (4) may adhere to the cover when the cover is removed.
- Remove carrier assembly (5) from the housing.
- Remove sun gear (6) from the carrier assembly.
Show/hide table
Illustration 2 g01033015 - Perform the following steps to disassemble carrier assembly (5).
- Locate pin (13) that holds bearing shaft (14) in carrier (15).
- Drive pin (13) fully into bearing shaft (14). Ensure that the pin is fully inserted. Damage to the carrier could occur when bearing shaft (14) is removed.
- Remove bearing shaft (14) from carrier (15). Remove pin (13) from bearing shaft (14).
- Slide planet gear (12) and four thrust washers (10) from carrier (15).
- Remove needle bearings (11) from inside the planet gear (12).
- Repeat steps 5.a through 5.e for each of the two remaining planet gears.
Show/hide tableIllustration 3 g01033021 - Remove three retaining rings (19) from spindle (22). Remove gear (20) and roller bearings (21) from each of the three shafts.
- Remove thrust spacer (25) and coupling (26) from inside housing (8). Remove external retaining ring (27) and internal retaining ring (24) from the coupling.
- Use Tooling (A) to remove bearing nut (28) from the spindle.
- Flip the housing and the spindle. Use a soft hammer to tap on the flange of housing (8). Separate housing (8) and bearing cone (29) from spindle (22).
- If necessary, remove bearing cup (16) and bearing cup (30) from housing (8).
- Remove bearing cone (17) from spindle (22).
- Remove Duo-Cone Conventional Seal (18) and (23) from the spindle.
- Flip the spindle.
Show/hide table
Illustration 4 g01033039 Show/hide tablePersonal injury can result from being struck by parts propelled by a released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to release the spring force.
- Install 11 M5 X 0.8 X 20 mm socket head screws (37) in thrust plate (35) to compress nine springs (34) and relieve the spring pressure on retaining ring (36).
- Remove retaining ring (36) from spindle (22).
- Remove piston (33) from the spindle.
- Remove backup ring (41) and O-ring seal (42) from spindle (22). Remove backup ring (32) and O-ring seal (31) from the spindle .
- Remove six plates (39), seven disks (40), and end plate (38) from spindle (22).
- Loosen 11 socket head screws (37) evenly to relieve the spring pressure on thrust plate (35). Remove the socket head screws. Remove the thrust plate and nine springs (34) from piston (33).
Show/hide table
Illustration 1 | g01033012 |
Caterpillar Information System:
785G Off-Highway Truck Power Train Oil Filter and Base (Torque Converter) - Disassemble
RM500B Reclaimer Mixer Machine Systems Piston Pump (Water Spray) - Assemble
RM500B Reclaimer Mixer Machine Systems Piston Pump (Water Spray) - Disassemble
3516E Engine for Tier 4 Final 994K Wheel Loaders Electrical Power Supply - Test
3516E Engine for Tier 4 Final 994K Wheel Loaders Sensor (Data Link Type) - Test
Installation Instruction for Self-Level Harness Protection Is Now Available for D-Series Skid Steer Loaders, Multi-Terrain Loaders, and Compact Track Loaders {5112, 5264, 5479} Installation Instruction for Self-Level Harness Protection Is Now Available for D-Series Skid Steer Loaders, Multi-Terrain Loaders, and Compact Track Loaders {5112, 5264, 5479}
3516E Engine for Tier 4 Final 994K Wheel Loaders DEF Pump - Replace
Procedure for Installing a Rear Horn 387-6549 Rocker Switch on Certain 415F2 and 416F2 Backhoe Loaders {1408} Procedure for Installing a Rear Horn 387-6549 Rocker Switch on Certain 415F2 and 416F2 Backhoe Loaders {1408}
994K Wheel Loader Transmission Breather - Clean
3516E Engine for Tier 4 Final 994K Wheel Loaders DEF Tank Level Is Low
CW12 Compactors Machine Systems Fuel Tank
CW12 Compactors Power Train Propel Lines Group
CP34 and CS34 Vibratory Soil Compactors Machine Systems Final Drive Planetary (Drum Propel) - Assemble
New Screws Are Now Used in the Left-Hand Side and Right-Hand Side Door Groups of Certain 773E, 777D, and 777E Off-Highway Trucks {7308} New Screws Are Now Used in the Left-Hand Side and Right-Hand Side Door Groups of Certain 773E, 777D, and 777E Off-Highway Trucks {7308}
986K Wheel Loader Engine Supplement Engine Oil Cooler - Remove and Install
AP655F and AP655F L Asphalt Paver Machine Systems Hopper
Improved Front Axle Group Components Are Now Used on Certain 24H and 24M Motor Graders {3020, 3282, 4305, 5225} Improved Front Axle Group Components Are Now Used on Certain 24H and 24M Motor Graders {3020, 3282, 4305, 5225}
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Rear Steering) - Disassemble
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Rear Steering) - Assemble
Recommended Shims to Adjust the Extra Free Play on Certain Compact Track Loaders, Multi-Terrain Loaders, and Skid Steer Loaders {5102, 5104, 6119, 6130} Recommended Shims to Adjust the Extra Free Play on Certain Compact Track Loaders, Multi-Terrain Loaders, and Skid Steer Loaders {5102, 5104, 6119, 6130}
Improvements to Global Positioning System (GPS) Antenna is Now Used for Certain Cat® Products {7220, 733B, 7347} Improvements to Global Positioning System (GPS) Antenna is Now Used for Certain Cat® Products {7220, 733B, 7347}
An Additional Rear Counterweight Kit Is Now Used on Certain 424B and 424B HD Backhoe Loaders {7056} An Additional Rear Counterweight Kit Is Now Used on Certain 424B and 424B HD Backhoe Loaders {7056}
An Improved Assembly Procedure for the Radiator Grill Lock Is Now Used on Certain 416F2 and 420F2 Backhoe Loaders {7170} An Improved Assembly Procedure for the Radiator Grill Lock Is Now Used on Certain 416F2 and 420F2 Backhoe Loaders {7170}
SE50 VT Asphalt Screed Inverter - Remove and Install