Procedure To Change Operator Controls From The Plus Pattern To The Cross Pattern {5063} Caterpillar

Backhoe Loader

426 F2 (S/N: EJ21-UP; DJ41-UP; EJ41-UP)

Introduction

This Special Instruction outlines the basic procedures to change operator controls from the plus pattern to the cross pattern.

Illustration 1	g06038074
Plus and Cross Patterns (A) Plus Pattern (B) Cross Pattern (C) Boom Lower (D) Swing Right (E) Boom Raise (F) Swing Left (G) Stick Out (H) Bucket Dump (I) Stick In (J) Bucket Crowd

When the controls are in the plus pattern, the levers move straight up and back, and side to side as shown in Illustration 1. When the controls are in the cross pattern, the levers move in an angular pattern. These instructions detail the conversion process.

Do not perform any of the procedures until you have read and understand the information in this publication.

Caterpillar Channel 1 Videos

For supplemental information on this procedure, refer to the following video. The previous training has been replaced with the video below.

Note: A CWS login is required to access Caterpillar Channel 1. Scan the QR code below with a QR enabled device or copy the link that follows.

Illustration 2	g06306276

Reference: Torque Specifications, SENR3130

Important Safety Section

Improper operation, lubrication, maintenance, or repair of this product can be dangerous and could result in injury or death.

The information, specifications, and illustrations in this publication are based on information that was available at the time that the publication was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other items can change at any time. These changes can affect the service that is given to the product. Obtain the complete and most current information before you start any job. Cat dealers have the most current information available.

Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.

Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard.

Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. If the tools, the procedure, the work method, or your actions are not recommended by Caterpillar, ensure that the tools and your actions are safe for you and for others.

Ensure that all personnel are safe when using a tool, procedure, work method, or operating technique not recommended by Caterpillar. Ensure that the product will not be damaged or the product made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used.

Show/hide table

Before service work is begun, park the machine on a hard level surface. Block the wheels of the machine so unexpected movement will not occur. Unexpected movement of the machine can cause personal injury or death.

Show/hide table

Personal injury or death can result from sudden machine movement. Sudden movement of the machine can cause injury to persons on or near the machine. To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.

Show/hide table

Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.

Graphic Color Description

Color-coding of targeted components, or sections of a part, is used to communicate a required action.

The descriptions below illustrate the different colors and what is represented when used in a graphic.

(Blue) The primary component of focus for a particular step. Target or primary component to be installed or removed. Installation implied unless otherwise noted with a symbol.

(CAT® Yellow) Description of parts.

(Yellow) Components placed aside for access, but not removed. Highlighted areas of adjustment, inspection, or special attention.

(Cyan) Special tools or other equipment required for use in a particular step.

(Light Gray) Components used for reference.

(Magenta) Any fastener, retainer, or electrical connector used to install or remove the primary component.

Graphic Symbol Description

This section includes all the symbol graphics used throughout the Visual Service Procedure (VSP), along with a brief description of what the symbol represents.

Apply Sealant - To apply an unbroken line of sealing material having the specified thickness or diameter.

Keep, Store - To retain for reinstallation or reuse.

Loosen - To make less tight. To set free. To release.

Level - To position a surface in a horizontal orientation. To position in vertical dimension. To align to assist positioning a surface in a horizontal orientation.

Lower - To drop to a reduced energy position. To reduce the level of material in a container. To cause to descend.

Open - To unseal or get access to.

Operation and Maintenance Manual

Position - To locate to the desired or intended location.

Remove - To take off.

Replace - To restore, or return, to a former or proper place.

Rotate - Clockwise - To turn on an axis. To alternate position or orientation, for the purpose of achieving even wear.

Rotate - Counter Clockwise - To turn on an axis. To alternate position or orientation, for the purpose of achieving even wear.

Service Indicator - Refer to a Technical Manual, Warning, Caution, or Notice

Required Tools

Machine Preparation

Illustration 3	g06224284

Illustration 4	g06224292
Refer to Testing and Adjusting, UENR3747, " System Pressure - Release".

Illustration 5	g06224535
Refer to Operation and Maintenance Manual, SEBU9213, " Battery Disconnect".

Converting Plus Pattern to Cross Pattern

Illustration 6	g06220852

Illustration 7	g06220868

Illustration 8	g06220872

Illustration 9	g06220897

Illustration 10	g06220924

Illustration 11	g06220932

Illustration 12	g06220939

Illustration 13	g06220941