Gear Motor (Fan Drive) - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0510 | Driver Gp | 1 |
- Use Tooling (A) to install lip seal (17) into mounting flange (10).
- Install retaining ring (16).
Show/hide table
Illustration 2 g03863249 - Install seal group (15) onto bearing housing (14).
Show/hide table
Illustration 3 g03863237 - Install bearing housing (14) onto mounting flange (10).
Note: Bearing housing (14) must be installed with the seal group against mounting flange (10).
- Install gears (12) and (13) into bearing housing (14).
Show/hide table
Illustration 4 g03863211 - Install O-ring seal (11) into motor housing (8).
Show/hide table
Illustration 5 g03863207 - Install motor housing (8) onto mounting flange (10).
Show/hide table
Illustration 6 g03863200 - Install seal group (9) onto bearing housing (7).
Show/hide table
Illustration 7 g03863179 - Install bearing housing (7).
- Install O-ring seal (6) onto motor housing (8).
Show/hide table
Illustration 8 g03863174 - Install cover (4).
- Install bolts (3) and the washers into cover (4). Tighten bolts (3) to a torque of
63 N·m (46 lb ft) . - Install elbow (5) and the O-ring seal.
Show/hide table
Illustration 9 g03863166 - Install O-ring seals (2) into elbows (1).
Show/hide table
Illustration 10 g03863157 - Install elbows (1) onto the piston motor.
Show/hide table
Illustration 1 | g03863247 |
End By:
- Install gear motor (fan drive).
Caterpillar Information System:
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Gear Motor (Fan Drive) - Disassemble
CW34 Pneumatic Compactor Machine Electronic Control System Determining Diagnostic Trouble Codes
MSS3s Machine Security System ECM - Replace
MSS3s Machine Security System ECM Software - Install
740 GC, 740 Ejector, 745 Articulated Truck Power Train Differential and Bevel Gear (Front and Rear) - Remove and Install
CP44B and CS44B Vibratory Soil Compactors Machine Systems Control Valve (Leveling Blade) - Remove and Install
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Fan Guard - Remove and Install
777D and 777E Off-Highway Truck Air System and Brakes Gear Pump (Torque Converter Charging, Scavenge, and Parking Brake Release)
CW34 Pneumatic Compactor Machine Electronic Control System Diagnostic Trouble Codes
16M Series 3 and 18M Series 3 Motor Grader Machine Preparation
Installing the 484-8211 Battery Disconnect Kit {1411} Installing the 484-8211 Battery Disconnect Kit {1411}
2015/08/05 A New Pinout Configuration Has Been Approved For Use on The Water In Fuel Sensor (WIF) Harness Connector on Certain Wheel Feller Bunchers {1408, 7490, 7610, 7620}
CW34 Pneumatic Compactor Machine Electronic Control System Emerging Symptom Information
CW34 Pneumatic Compactor Machine Electronic Control System Machine Movement Without Request
CW34 Pneumatic Compactor Machine Electronic Control System CAN Data Link - Test
CW34 Pneumatic Compactor Machine Electronic Control System Relay - Test
CW34 Pneumatic Compactor Machine Electronic Control System Solenoid Valve - Test
CW34 Pneumatic Compactor Machine Electronic Control System Sensor Supply - Test
PL72 Pipelayers Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
CW34 Pneumatic Compactor Machine Electronic Control System Sensor Signal (Analog, Passive) - Test
CW34 Pneumatic Compactor Machine Electronic Control System Speed Sensor (Dual Signal) - Test
CW34 Pneumatic Compactor Machine Electronic Control System Switch Circuits - Test
CW34 Pneumatic Compactor Machine Electronic Control System ECM Software - Install
CW34 Pneumatic Compactor Machine Electronic Control System Connector Contact Description