Gear Motor (Fan Drive) - Disassemble
Start By:
- Remove the gear motor (fan drive).
- Remove elbows (1) from the piston motor.
Show/hide table
Illustration 2 g03863166 - Remove O-ring seals (2) from elbows (1).
Show/hide table
Illustration 3 g03863174 - Remove elbow (5) and the O-ring seal from cover (4).
- Remove bolts (3) and the washers from cover (4).
- Remove cover (4).
Show/hide table
Illustration 4 g03863179 - Remove O-ring seal (6) from motor housing (8).
- Remove bearing housing (7).
Show/hide table
Illustration 5 g03863200 - Remove seal group (9) from bearing housing (7).
Show/hide table
Illustration 6 g03863207 - Remove motor housing (8) from mounting flange (10).
Show/hide table
Illustration 7 g03863211 - Remove O-ring seal (11) from motor housing (8).
Show/hide table
Illustration 8 g03863237 - Remove gears (12) and (13) from bearing housing (14).
- Remove bearing housing (14).
Show/hide table
Illustration 9 g03863249 - Remove seal group (15) from bearing housing (14).
Show/hide table
Illustration 10 g03863247 - Remove retaining ring (16) and lip seal (17) from mounting flange (10).
Show/hide table
Illustration 1 | g03863157 |
Caterpillar Information System:
CW34 Pneumatic Compactor Machine Electronic Control System Determining Diagnostic Trouble Codes
MSS3s Machine Security System ECM - Replace
MSS3s Machine Security System ECM Software - Install
740 GC, 740 Ejector, 745 Articulated Truck Power Train Differential and Bevel Gear (Front and Rear) - Remove and Install
CP44B and CS44B Vibratory Soil Compactors Machine Systems Control Valve (Leveling Blade) - Remove and Install
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Fan Guard - Remove and Install
777D and 777E Off-Highway Truck Air System and Brakes Gear Pump (Torque Converter Charging, Scavenge, and Parking Brake Release)
CW34 Pneumatic Compactor Machine Electronic Control System Diagnostic Trouble Codes
16M Series 3 and 18M Series 3 Motor Grader Machine Preparation
Installing the 484-8211 Battery Disconnect Kit {1411} Installing the 484-8211 Battery Disconnect Kit {1411}
2015/08/05 A New Pinout Configuration Has Been Approved For Use on The Water In Fuel Sensor (WIF) Harness Connector on Certain Wheel Feller Bunchers {1408, 7490, 7610, 7620}
New Pinouts For Water In Fuel Harness (WIF) Connector When New Engine Ratings Electronic Software Gp Is Installed on Certain Wheel Feller Buncher{1408, 7490, 7610, 7620} New Pinouts For Water In Fuel Harness (WIF) Connector When New Engine Ratings Electronic Software Gp Is Installed on Certain Wheel Feller Buncher{1408, 7490, 7610, 7620}
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Gear Motor (Fan Drive) - Assemble
CW34 Pneumatic Compactor Machine Electronic Control System Emerging Symptom Information
CW34 Pneumatic Compactor Machine Electronic Control System Machine Movement Without Request
CW34 Pneumatic Compactor Machine Electronic Control System CAN Data Link - Test
CW34 Pneumatic Compactor Machine Electronic Control System Relay - Test
CW34 Pneumatic Compactor Machine Electronic Control System Solenoid Valve - Test
CW34 Pneumatic Compactor Machine Electronic Control System Sensor Supply - Test
PL72 Pipelayers Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
CW34 Pneumatic Compactor Machine Electronic Control System Sensor Signal (Analog, Passive) - Test
CW34 Pneumatic Compactor Machine Electronic Control System Speed Sensor (Dual Signal) - Test
CW34 Pneumatic Compactor Machine Electronic Control System Switch Circuits - Test
CW34 Pneumatic Compactor Machine Electronic Control System ECM Software - Install