Axle Shaft - Remove and Install
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-5832 | 撬杆 | 1 |
B | 2P-8312 | 挡圈钳 | 1 |
C | 1U-8848 | 轮轴安装器 | 1 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
Show/hide table
图 1 | g01191324 |
注: 由于半轴内部采用双列花键,因此左侧半轴必须采用以下程序。 如果采用正常拆卸程序,双列花键将卡住差速锁。
- 通过移动车轮将排放螺塞 (1) 定位到盖 (2) 的底部。 拆下排放塞,以便让机油排入适当的容器。
- 拆下螺栓 (3) 和垫圈。 将盖 (2) 和 O 形密封圈 (4) 从终传动上拆下。
Show/hide table
图 4 g01191482 Show/hide table图 5 g01191484 - 利用工具 (A) 定位半轴 (5),从而使太阳齿轮 (6) 与终传动齐平。 通过向后推太阳齿轮 (6) 接近挡圈 (7)。 使用工具 (B) 拆下挡圈 (7)。 拆下太阳齿轮 (6)。
Show/hide table
图 6 g01191487 - 使用工具 (B) 安装挡圈 (7)。 挡圈 (7) 将用于防止工具 (C) 损坏。
Show/hide table
图 7 g01191490 Show/hide table图 8 g01191491 - 将适当的起吊设备和工具 (C) 固定到半轴 (5) 上。 半轴 (5) 的重量约为
35 kg (75 lb) 。 通过将半轴 (5) 充分拉出终传动拆下工具 (C) 和重新定位适当的起吊设备。 拆下半轴 (5)。
Show/hide table
图 2 | g01416760 |
Show/hide table
图 3 | g01191343 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-5832 | 撬杆 | 1 |
B | 2P-8312 | 挡圈钳 | 1 |
- 通过移动车轮将排放螺塞 (1) 定位到盖 (2) 的底部。 通过拆下排放螺塞进行放油。
- 拆下螺栓 (3) 和垫圈。 将盖 (2) 和 O 形密封圈 (4) 从终传动上拆下。
Show/hide table
图 11 g01191482 Show/hide table图 12 g01191496 - 利用工具 (A) 定位半轴 (5),从而使太阳齿轮与终传动齐平。
- 将适当的起吊设备固定到半轴 (5) 上。 半轴 (5) 的重量约为
35 kg (75 lb) 。 拆下半轴 (5)。Show/hide table图 13 g00846992 - 利用工具 (B) 将挡圈 (7) 从半轴 (5) 上拆下。 拆下太阳齿轮 (6)。
Show/hide table
图 9 | g01191341 |
Show/hide table
图 10 | g01191343 |
注: 清洁度是一项重要的因素。 安装步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
Show/hide table
图 14 | g01191336 |
注: 左右半轴将采用相同的安装程序。 左侧半轴具有差速锁必须接合的双列花键。
- 安装挡圈 (7)。 挡圈 (7) 将用于防止工具 (C) 损坏。 将适当的起吊设备固定到半轴 (5) 上。 半轴 (5) 的重量约为
35 kg (75 lb) 。 安装半轴 (5)。 利用工具 (C) 将半轴 (5) 的花键对准插入差速器。Show/hide table图 17 g01191484 Show/hide table图 18 g01191546 - 拆下挡圈 (7)。 安装太阳齿轮 (6)。 利用螺丝刀升起半轴 (5),从而可以完全安装太阳齿轮 (6) 而无需将半轴 (5) 进一步推入终传动。 安装挡圈 (7)。
Show/hide table
图 19 g01191343 Show/hide table图 20 g01416760 - 安装 O 形密封圈 (4)。 安装终传动的盖 (2)。 安装螺栓 (3)。 将排放螺塞 (1) 安装到盖 (2) 的底部。
- 检查终传动的油位。 必要时添加机油。 请参考操作和保养手册, "差速器和终传动油 - 更换"。
Show/hide table
图 15 | g01191553 |
Show/hide table
图 16 | g01191490 |
Caterpillar Information System:
2015/07/10 An Improved Aftercooler Air Lines Clamp Installation Procedure Is Now Used on Certain Articulated Trucks {1071}
MH3022, MH3024 and MH3026 Material Handlers Machine System Specifications Hydraulic Fan Drive Lines
M318F, M320F and M322F Wheeled Excavators Machine System Specifications Tire and Rim
M318F, M320F and M322F Wheeled Excavators Machine System Specifications Tire and Rim
994K Wheel Loader Machine Systems Steering Control Valve (with Secondary Steering)
M316D, M318D, M320D2, M322D, M322D 2 MH, M322D2 and M324D 2 MH Wheeled Excavators Machine System Specifications Swing Drive
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Main Control Valve
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
MH3022, MH3024 and MH3026 Material Handlers Machine System Specifications Suction Fan
M318F, M320F and M322F Wheeled Excavators Machine System Specifications Hydraulic Fan Drive Lines
994K Wheel Loader Machine Systems Gear Pump (Secondary Steering)
M316D, M318D, M320D2, M322D, M322D 2 MH, M322D2 and M324D 2 MH Wheeled Excavators Machine System Specifications Boom Cylinder
MSS3s Machine Security System Determining Diagnostic Trouble Codes
MSS3s Machine Security System Electrical Power Supply - Test
740 GC, 740 Ejector, 745 Articulated Truck Power Train Front Axle - Remove and Install
Procedure to Replace Noncurrent Gear Pumps on Certain Articulated Trucks {5073} Procedure to Replace Noncurrent Gear Pumps on Certain Articulated Trucks {5073}
MSS3s Machine Security System Cat Data Link - Test
525D, 535D, 545D and 555D Wheel Skidders General Information
482-7519 Feeler Gage Tool Group{0374, 0599, 0700, 0701, 0703, 0705, 0759, 1100, 1102, 1105, 1121, 1123} 482-7519 Feeler Gage Tool Group{0374, 0599, 0700, 0701, 0703, 0705, 0759, 1100, 1102, 1105, 1121, 1123}
CCS7 Combination Vibratory Compactors Machine Systems Vibratory Support - Disassemble
CCS7 Combination Vibratory Compactors Machine Systems Vibratory Support - Assemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
MD6200 Rotary Drill System Pressure Release
MD6200 Rotary Drill Operating Technique Information