Pilot Valve (STIC Steering) - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | Loctite Graphite 50     | -     |
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
- Apply Tooling (A) to the threads of three bolts (9) .
Show/hide table
Illustration 1 | g03738762 |
- Install lockout assembly (10) and STIC steering pilot valve (11) using three bolts (9), the nuts, and the washers.
- Connect electrical connector (7) and electrical connector (8) .
Show/hide table
Illustration 2 | g03738761 |
- Connect hose assembly (3), hose assembly (4), hose assembly (5) and hose assembly (6) .
- Loosen two locknuts (13). With the STIC steering pilot valve in the center position, adjust plate (14) in order to engage the mechanical lockout. Tighten locknuts (13). Operate lever (12) to lock and unlock the mechanical lockout assembly and check for a smooth operation.
Show/hide table
Illustration 3 | g03738759 |
- Check the STIC lockout control limit switch. Refer to Testing and Adjusting, "Limit Switch STIC Lockout Control - Check".
- Install cover (1) and cover (2) .
Note: Connect the electrical connector for the step lamp attached to cover (1) .
Show/hide table
Illustration 4 | g03738758 |
- Fill the hydraulic tank with oil to the correct level. Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check".
- Adjust the steering deadband. Refer to Systems Operation, Testing and Adjusting, "STIC Control (Steering Deadband) - Adjust".
End By: Remove the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Caterpillar Information System:
2014/10/27 Improved Solenoid Valve Group Is Now Used On Certain Load Haul Dumps and Wheel Loaders {3073, 3139, 5479}
PL83 and PL87 Pipelayers Mounting and Dismounting
735C and 745C Articulated Trucks Machine Systems Power Train Hydraulic System
RM500B Reclaimer Mixer Machine Systems Relief Valve (Charge, Emulsion Spray) - Test and Adjust
AP500F Asphalt Paver Stopping the Machine
RM500B Reclaimer Mixer Machine Systems Emulsion Pump - Test
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Electronic Control (Machine System)
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Location of Components (Machine System)
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System General Information (Machine System)
794 AC Off-Highway Truck Engine Supplement Engine Oil Cooler - Remove and Install
M318F, M320F and M322F Wheeled Excavators Hydraulic System Case Drain (Travel Motor) - Test
428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Seat - If Equipped
RM500B Reclaimer Mixer Machine Systems Engine Enclosure (Hood)
RM500B Reclaimer Mixer Machine Systems Hood - LH
RM500B Reclaimer Mixer Machine Systems Hydraulic Tank
RM500B Reclaimer Mixer Machine Systems Rotor Brake
RM500B Reclaimer Mixer Machine Systems Rotor Drive Shaft
RM500B Reclaimer Mixer Machine Systems Hood - RH
RM500B Reclaimer Mixer Machine Systems Hydraulic Cylinder (Hood Tilt)
2014/10/27 New Converter Impeller and Impeller Hub are Now Used on Certain 24M Motor Graders {3101}
2014/11/13 New Transmission Software to Prevent Excessive Ejector Blade Drift When the Machine is Stationary on an Incline is Available for Certain Articulated Trucks {7620}
2014/11/10 A New Installation Procedure is Used for the Clean Emissions Module (CEM) Fan Components on Certain Articulated Trucks {1050}
2014/10/27 An Improved Installation Procedure for the Injector Top O-Ring Seal on C27 and C32 Machine Engines {1251, 1254, 1290, 1713}
2014/10/27 New Guidelines for Valve Cover Base Threaded Insert on C27 and C32 Engines {1107, 1120}