Diesel Particulate Filter - Remove and Install
Start By:
- Remove inlet module (catalyst).
- Put Identification Mark (A) across clamp assembly (1), diesel particulate filter (3), and outlet assembly (4). Identification Mark (A) is for assembly purposes.
- Put Identification Mark (B) on the diesel particulate filter (3) for installation purposes. Identification Mark (B) is showing the flow of exhaust gases through diesel particulate filter (3).
- Disconnect clamp assembly (1) and clamp assembly (2). Separate diesel particulate filter (3) from outlet assembly (4). Remove diesel particulate filter (3).
Show/hide table
Illustration 1 | g03513039 |
Show/hide table
Illustration 2 | g03513036 |
Note: Do not allow any objects to contact the internal element of diesel particulate filter (3). Do not bump or shake the filter assembly.
- Install diesel particulate filter (3) in the reverse order of removal.
- Install new clamp assembly (1). Torque the new clamp assemblies (1) to a torque of
60 ± 5 N·m (44 ± 4lb ft) . Do not use power tools in order to tighten clamp assemblies (1). - Tighten clamp (2) to a torque of
15 ± 3 N·m (133 ± 27 lb in) . - Reset the engine ash model. Refer to Special Instructions , REHS5026.
- Install new clamp assembly (1). Torque the new clamp assemblies (1) to a torque of
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Turbocharger
C4.4 Engines for Caterpillar Built Machines Fuel Injection Pump
C4.4 Engines for Caterpillar Built Machines Fuel Filter Base - Twin Secondary Fuel Filter Base
14L Motor Grader Battery - Remove and Install
C4.4 and C7.1 Engines Fuel Pressure Problem
994K Wheel Loader Service Center
Cat ® Fleet Onboard Software Version 3.1 Locks Up{7605} Cat ® Fleet Onboard Software Version 3.1 Locks Up{7605}
C13, C15, and C18 Tier 4 Final Engines Gear Group (Front)
C4.4 Engines for Caterpillar Built Machines Gear Group (Front)
2013/12/09 An Improved Routing Process is Now Available When Replacing 192-7805 Harness As in TLV1 Seat Suspensions on Certain Machines {1408, 7312, 7324}
725C, 725C2, 730C and 730C2 Articulated Truck Systems Calibrations (Cat ET)
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Drive Shaft
730C2 Articulated Truck Cooling System Water Temperature Regulator - Replace
730C and 730C2 EJECTOR Articulated Truck Systems Ejector Circuit
730C EJECTOR Articulated Truck Service Brake Control
730C EJECTOR Articulated Truck Engine Compression Brake Control
836K Landfill Compactor, 834K Wheel Dozer and 988K Wheel Loader Power Train Power Train Oil Filter Bypass Valve - Remove and Install
Rear Final Drive Brake and Wheel Group Assembly and Disassembly System{0374, 0599, 0700, 0727, 0730, 0731} Rear Final Drive Brake and Wheel Group Assembly and Disassembly System{0374, 0599, 0700, 0727, 0730, 0731}
24 Motor Grader Engine Crankcase Breather - Clean
Procedure to Install a Flow Through Diesel Particulate Filter on R1700G Load Haul Dump Machines Equipped with Ventilation Reduction Package{1089} Procedure to Install a Flow Through Diesel Particulate Filter on R1700G Load Haul Dump Machines Equipped with Ventilation Reduction Package{1089}
Procedure to Install a Flow Through Diesel Particulate Filter on R1600H Load Haul Dump Machines Equipped with Ventilation Reduction Package{1089} Procedure to Install a Flow Through Diesel Particulate Filter on R1600H Load Haul Dump Machines Equipped with Ventilation Reduction Package{1089}
C15 and C18 Engines for Caterpillar Built Machines Valve Rocker Arm
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector Rocker Arm
C15 and C18 Engines for Caterpillar Built Machines Gear Group (Rear)