Nitrogen Oxide Sensor - Remove and Install - Inlet
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Loctite Nickel Anti-seize | - |
Show/hide table
 |
|
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- Disconnect sensor (1). Cut cable strap (2).
Show/hide table
Illustration 2 g03502336 - Cut cable straps (3).
Show/hide table
Illustration 3 g03504009 - Remove panel (4).
Show/hide table
Illustration 4 g03502337 - Cut cable strap (7). Disconnect harness assemblies (6). Remove nitrogen oxide sensor (5).
Show/hide table
| |
| Illustration 1 | g03502335 |
Note: New nitrogen oxide sensors are pre-lubricated. Do not use Tooling (A) on new nitrogen oxide sensors. When installing an existing nitrogen oxide sensor install Tooling (A) on the threads only.
Note: or more information about nitrogen oxide sensors, refer to Special Instruction, REHS8151, "NOx Sensors Handling and Installation Procedures".
- Install nitrogen oxide sensor (5) in the reverse order of removal.
- Tighten nitrogen oxide sensors (5) to a torque of
50 ± 10 N·m (37 ± 7 lb ft) .
- Tighten nitrogen oxide sensors (5) to a torque of
Caterpillar Information System:
2013/11/15 New Pressure Switch Is Now Used for the Air Conditioner Lines Group on Certain Motor Graders {1808}
966M and 972M Wheel Loaders Plate Locations and Film Locations
2015/01/16 New Pin Assemblies are Now Used in the Truck Body Mounting Groups on Certain Off-Highway Trucks {7258, 7258}
988K Wheel Loader, 834K Wheel Dozer and 836K Compactor Machine Systems Parking Brake - Remove and Install
2013/10/31 New Metering Pump Group Is Now Introduced in 424B Backhoe Loader {4312}
Check the STIC Control on Certain R1700G, R2900G and R3000H Load Haul Dump Machines{3034, 4343} Check the STIC Control on Certain R1700G, R2900G and R3000H Load Haul Dump Machines{3034, 4343}
2013/12/06 Correction to Disassembly and Assembly , "Parking Brake - Install" for Certain R1600G Load Haul Dump Machines {4267}
836K Landfill Compactor and 834K Wheel Dozer Machine Systems Front Frame to Rear Frame - Connect
836K Landfill Compactor and 834K Wheel Dozer Machine Systems Front Frame from Rear Frame - Separate
836K Landfill Compactor and 834K Wheel Dozer Machine Systems Hydraulic Tank - Assemble
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Location of Components (Hydraulic System)
14L Motor Grader Catalyst (SCR) - Remove and Install
2014/01/23 New Air Dryer Is Now Used on Certain K and K Series 2 Motor Graders {4285}
Release Notes for Cat® MineStar v3.x.x System{7605} Release Notes for Cat® MineStar v3.x.x System{7605}
14L Motor Grader Nitrogen Oxide Sensor - Remove and Install - Outlet
2013/11/08 New Product Link and VIMS3G Software for 523, A4:N4 Modules Is Now Available for Certain Large Wheel Loaders {7601, 7606}
988K Wheel Loader, 834K Wheel Dozer and 836K Compactor Machine Systems Electrohydraulic Control (Joystick) - Remove and Install
14L Motor Grader Ignition Coil - Remove and Install - CEM
14L Motor Grader Inlet Module (Catalyst) - Remove and Install - Catalyst
Command for Underground Amber Machine Automation System Warning Light Circuit - Test
Command for Underground Server Software - Update - Machine Automation System (MAS)
Procedure to Rework the Air Conditioner Compressor Mount on R2900G and R3000H Load Haul Dump Machines{1802} Procedure to Rework the Air Conditioner Compressor Mount on R2900G and R3000H Load Haul Dump Machines{1802}
Command for Underground Radio Firmware - Update - MAS and LARN
Command for Underground Radio Firmware - Reset - Factory Default