Installation Of 1W4793 Governor Spring (High Idle){1264, 1265}
Usage:
3208 ( 40S, 32Y)
Make reference to the Service Manual for governor spring replacement procedure. After installation of this governor spring, see your Caterpillar Dealer for specific adjustment and modification procedures that are necessary because of EPA (Environmental Protection Agency) standards for noise; and for throttle (accelerator) return time from high idle speed-to-low idle speed.
Caterpillar Information System:
Use Of 6V4141 Sleeve Metering Calibration Tool Group{0778, 0782} Use Of 6V4141 Sleeve Metering Calibration Tool Group{0778, 0782}
Installation Of Electric (Digital) Tachometer Groups{7462} Installation Of Electric (Digital) Tachometer Groups{7462}
Installation of 5N7710 Fuel Injection Lines Group And 5N7741 Fuel Lines Drain Group{1250} Installation of 5N7710 Fuel Injection Lines Group And 5N7741 Fuel Lines Drain Group{1250}
Installation Of Replacement Parts For 3N7722, 8N2744, 1W1872, 1W1873, 1W1881 and 1W1882 Engine Oil Pump Groups{1304} Installation Of Replacement Parts For 3N7722, 8N2744, 1W1872, 1W1873, 1W1881 and 1W1882 Engine Oil Pump Groups{1304}
2W715 Turbocharger Cartridge Repair Kit{1053} 2W715 Turbocharger Cartridge Repair Kit{1053}
Installation Of 8N6414 Ether Starting Aid Group{1456} Installation Of 8N6414 Ether Starting Aid Group{1456}
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264} Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Use Of 8T0455 Cylinder Liner Projection Indicator Group{0760, 1216} Use Of 8T0455 Cylinder Liner Projection Indicator Group{0760, 1216}
Installation Of Replacement Drive Sleeve For Marine Transmission Oil Pump{3310} Installation Of Replacement Drive Sleeve For Marine Transmission Oil Pump{3310}
Installation Of 5N5880 Remote Shut-Off Group And 5N6336 Gauge Group{7400, 7418} Installation Of 5N5880 Remote Shut-Off Group And 5N6336 Gauge Group{7400, 7418}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201} Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117} Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Assembly Of 6V97 Engine Stand{0630} Assembly Of 6V97 Engine Stand{0630}
Use Of 6V4040 Nitrogen Tire Inflation Group{4231} Use Of 6V4040 Nitrogen Tire Inflation Group{4231}
Use Of 6V4068 Tool Group For Installation Of 9N5822 Thrust Washer{1253} Use Of 6V4068 Tool Group For Installation Of 9N5822 Thrust Washer{1253}
Use Of 6V4805 Valve Seat Insert Puller Group{0703} Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Installation Of 5N7900 Air Starting Motor Lubricator{1451} Installation Of 5N7900 Air Starting Motor Lubricator{1451}
Use Of 6V4840 Tool Group To Install Water Ferrules{1201} Use Of 6V4840 Tool Group To Install Water Ferrules{1201}
Installation Of EMS (Electronic Monitoring System) Indicators{7450} Installation Of EMS (Electronic Monitoring System) Indicators{7450}
Installation Of Engine Block, Support Rails And/Or Oil Pan Base Assembly{1154, 1201, 1302} Installation Of Engine Block, Support Rails And/Or Oil Pan Base Assembly{1154, 1201, 1302}
Special Handling Information For Installation Of 2W1733 Or 2W1734 Crankshaft Seal Group{1160, 1161, 1202} Special Handling Information For Installation Of 2W1733 Or 2W1734 Crankshaft Seal Group{1160, 1161, 1202}
Installation Of 5N1948 And 2W3037 Sound Isolation Mounting Groups{1000, 3300, 7060} Installation Of 5N1948 And 2W3037 Sound Isolation Mounting Groups{1000, 3300, 7060}
Installation Of 6V4839 Cap And 15600 Snap Ring In 5P3508 Torque Multiplier{0614} Installation Of 6V4839 Cap And 15600 Snap Ring In 5P3508 Torque Multiplier{0614}
Using The 6V6000 Dial Bore Gauge Group{0761} Using The 6V6000 Dial Bore Gauge Group{0761}