Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300} Caterpillar


Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300}

Usage:

D399 (91B) D398 (67B) D379 (69B)

Indicates change

(1) Auxiliary Water Circuit-Pump Inlet Pressure (904).

(2) Auxiliary Water Circuit-Pump Outlet Pressure (905).

(3) Jacket Water Outlet Temperature (901).

(4) Jacket Water Pump Outlet Temperature (902).

(5) Intake Manifold Temperature (906). Intake Manifold Pressure (911).

(6) Air Inlet Restriction (907). Air Cleaner Outlet Temperature (930).

(7) Exhaust Stack Pressure (908). Exhaust Stack Temperature (912).

(8) Aftercooler Water Inlet Pressure (923).

(9) Aftercooler Water Outlet Pressure (924). Transmission Cooler-Water Inlet Temperature (925).

(10) Engine Oil Temperature (913).

(11) Engine Oil Pressure (914).

(12) Marine Gear Oil Temperature (915).

(13) Marine Gear Oil Pressure (916).

(14) Fuel Pressure (917).

(15) High Idle Speed (910). Low Idle Speed (910). Full Throttle Engine Speed (910). Minimum Engine Speed During Emergency Reverse (910).

(16) Engine Service Meter Reading (910).

Caterpillar Information System:

Introduction To Sea Trial Measurements Of Caterpillar Marine Engines{1000, 3300} Introduction To Sea Trial Measurements Of Caterpillar Marine Engines{1000, 3300}
Installation Of Governor Spring Guide{1264} Installation Of Governor Spring Guide{1264}
Installation Of 2W0172 Water Pump Seal Assembly With 5P9722 Driver{1361} Installation Of 2W0172 Water Pump Seal Assembly With 5P9722 Driver{1361}
Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218} Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264} Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253} Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Reconditioning Of Cylinder Heads For Use On Spacer Plate Cylinder Blocks{1101} Reconditioning Of Cylinder Heads For Use On Spacer Plate Cylinder Blocks{1101}
Troubleshooting And Repair Of The 5P6590 Wiring Harness Tester Group{0651} Troubleshooting And Repair Of The 5P6590 Wiring Harness Tester Group{0651}
Operating And Adjusting Instructions For 9S2000 Hydraulic Flow Meter{0784, 5050} Operating And Adjusting Instructions For 9S2000 Hydraulic Flow Meter{0784, 5050}
Installation Of 7N9013 Gasket Service Group{1101, 1221} Installation Of 7N9013 Gasket Service Group{1101, 1221}
Installation Of 7N142 Seal Group{1160} Installation Of 7N142 Seal Group{1160}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331} Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300} Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300}
Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300} Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300}
Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300} Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300}
Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300} Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300}
Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300} Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300}
Sea Trial Measurements On Caterpillar Marine Engine{1000, 3300} Sea Trial Measurements On Caterpillar Marine Engine{1000, 3300}
Tandem Engine Timing Procedure{1000} Tandem Engine Timing Procedure{1000}
Conversion Of The 1P3550 Wiring Harness Tester{0785, 1400} Conversion Of The 1P3550 Wiring Harness Tester{0785, 1400}
Installation Of 8N628 Bearing{7551, 1253} Installation Of 8N628 Bearing{7551, 1253}
Installation Of Hydra-Mechanical Shutoff Groups{7400, 7418} Installation Of Hydra-Mechanical Shutoff Groups{7400, 7418}
Installation Of 8N3104 Governor Conversion Group (Woodward PSG){1250} Installation Of 8N3104 Governor Conversion Group (Woodward PSG){1250}
Installation Of 6N8124 And 6N8127 Cylinder Block Assemblies{1201} Installation Of 6N8124 And 6N8127 Cylinder Block Assemblies{1201}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.