Brake System Air - Purge
Show/hide table
在以下步骤中,如果不是两人同时操作,可能造成人身伤亡。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
简介
此信息包括以下程序:
- 制动系统空气 - 净化
所需工具
Show/hide table
所需工具     | ||
数量     | 零件号     | 说明     |
根据需要使用     | N/A     | 透明管 6.4 mm (0.25'')     |
测试准备
通过完成正在维修的机器的测试和调整, "机器故障诊断和排除的准备"中指定的步骤,执行机器测试准备工作。
- 移动转向机架锁到锁定位置。
Show/hide table
图 1 | g03333657 |
转向机架处于锁定位置 |
- 停止发动机。 接合停车制动器。
测试步骤
Show/hide table
图 2 | g03344652 |
左前车桥壳体视图,其他拐角类似。 (1) 排气螺钉。 |
行车制动器的四个空气净化螺钉位于相应轴壳体顶端。
注: 每次对一个行车制动器进行该步骤。
- 检查液压油箱中的油位。 在整个排气过程中,确保液压油箱仍保持正确油位。
- 起动发动机。 使油压增至切断压力。
- 将直径为 6.4 mm (.25 in) 的透明油管一端固定于一个空气净化螺钉上。 将管的另一端置于合适的容器中,以收集液压油。 您还可将管引导回液压油箱。 松开排气螺钉 (1) 。
- 操作员应缓慢踩下制动踏板。 在整个步骤 5 中将制动器踏板固定到此位置。
- 当液压油流过管时,在机油中查看是否有气泡。 让油流入容器,直到看不到气泡为止。 随后上紧排气螺钉 (1) 。 松开制动踏板。
- 对其它每个行车制动器进行该步骤。 确保紧固所有空气净化螺钉。
- 如有必要,注满液压油箱。
注: 在操作开始的几个小时内,如果制动踏板不稳固,再次进行该步骤。
Caterpillar Information System:
2013/01/04 New Software for Integrated Brake Is Now Available for Certain 793F, 795F, and 797F Large Off-Highway Trucks {7620}
2013/01/10 New Software Is Now Available for Cat® Terrain for Drilling {7605, 7620}
2013/04/04 Procedure For Improving Compatibility of Product Link Is Now Available on Caterpillar Machines Equipped with Electronic Monitoring Systems (EMS) {7490, 7606}
2012/12/21 An Improved Transmission Harness Is Now Used for Certain Cat® Products {1408, 3167, 5736}
2012/12/24 A New Hose Assembly is Now Used in the Brake Cooling Lines Group on Certain 797F Off-Highway Truck {1365, 4257}
770G and 772G Off-Highway Truck Systems Accumulator Charging Valve
R1600H Load Haul Dump C11 Engine Supplement Coolant Level Sensor
R1600H Load Haul Dump C11 Engine Supplement Engine Mounting (Rear)
2012/12/20 Cat® Terrain Display Is Now Available With Improved Features For Certain Machine Control And Guidance Products {7490}
966M Tier 4, 966M Tier 4 Series XE, 972M Tier 4 and 972M Tier 4 Series XE Wheel Loaders Refrigerant Compressor - Remove and Install
Updating Certain Cat® Machines from EMS II to EMS III {7490, 7610, 7620} Updating Certain Cat® Machines from EMS II to EMS III {7490, 7610, 7620}
2012/12/18 An Adjusting Procedure is Available for the Exhaust Bypass Valve on High Altitude Arrangement (HAA) 797F Off-Highway Truck Engines {1057}
836K Landfill Compactor and 834K Wheel Dozer System Schematic
2013/03/01 New Suction Screen and Handle Are Used in 3500 Machine Engines {1302, 1302}
CB14B Vibratory Asphalt Compactor Machine Systems Visual Inspection
CB14B Vibratory Asphalt Compactor Machine Systems Machine Preparation for Troubleshooting
CB14B Vibratory Asphalt Compactor Machine Systems System Pressure - Release
CB14B Vibratory Asphalt Compactor Machine Systems Hydraulic Oil Contamination - Test
CB14B Vibratory Asphalt Compactor Machine Systems Gear Pump Flow - Test
Landfill Compactors, Soil Compactors, Wheel Dozers, and Wheel Loaders VIMSTM 3G Electrical Connector - Inspect
Landfill Compactors, Soil Compactors, Wheel Dozers, and Wheel Loaders VIMSTM 3G Wiring Harness (Open Circuit) - Test
Landfill Compactors, Soil Compactors, Wheel Dozers, and Wheel Loaders VIMSTM 3G Wiring Harness (Short Circuit) - Test
CB14B Vibratory Asphalt Compactor Machine Systems Relief Valve (Main) - Test and Adjust - Vibratory
2012/12/21 The Primer Color Has Changed for All C15 and C18 Machine Engine Blocks {1201, 7559}