Parts and Specification Information
| |
| Illustration 1 | g06388077 |
Note: Verify that all parts are shipped and undamaged for preparation of assembly. Missing or damaged parts can be ordered prior to assembly to avoid delays during assembly.
| Item | Part Number | Part Description | Qty | Specification | Approximate Weight | |
| 289-2316 Walkway Gp | ||||||
| 1 | 289-2316 | Walkway Gp | 1 | |
||
| 2 | 198-4778 | Hard Washers | 6 | |||
| 3 | 8T-4183 | Bolts
(M12X1.75X40-MM) |
6 | |||
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| T1 | 8T-3091 | Tap (M12X1.75) | 1 |
Start By:
- Install the right-hand walkway
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
 |
|
Observe the safe working load limits of all lifting and blocking devices and keep a safe distance from suspended/blocked loads. Personnel may be seriously injured or killed by falling loads. |
|
|
Personal injury or death can occur from heavy components falling during removal or installation. Properly support the component with a suitable lifting device during removal or installation. |
|
|
Personal injury or death can result from improper lifting or blocking. When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component. Approximate weights of the components are shown. Clean all surfaces where parts are to be installed. |
|
|
Do not attempt to assemble this machine until you read and you understand the assembly instructions. Improper assembly procedures could result in injury or death. |
Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting"
topic for safety information.
Note: Remove all protective shipping covers, flanges, plugs, caps, clamps, cable straps, and material.
Note: Clean mounting and contact surfaces for major component installation free of wax, dirt, debris, paint, and grease.
Note: If necessary, chase unprotected threaded holes with an appropriately sized tap to remove paint, rust, or other debris.
Note: Unless otherwise specified, all torque requirements are Standard Torque values. Refer to the "General Information" section in this document for the correct torque values.
Note: Before tightening the cable straps (mounting hardware), remove the slack from the harness assemblies and allow adequate strain relief.
- Clean the mating surface on the frame free of wax, dirt, debris, paint, and grease.
- Use Tooling (T1) to clean the threads of the six threaded holes.
Show/hide table
Illustration 3 g06388059 - Clean the mating surface of the walkway group free of wax, dirt, debris, paint, and grease.
Show/hide table
Illustration 4 g06388069 Show/hide table
Illustration 5 g06388072 (1) 289-2316 Walkway Gp
(2) 198-4778 Hard Washers
(3) 8T-4183 Bolts (M12X1.75X40-MM) - Use a suitable lifting device to install walkway group (1). The weight of walkway group (1) is approximately
79 kg (174 lb) . Install six hard washers (2) and six bolts (3).
| |
| Illustration 2 | g06388027 |
| (T1) 8T-3091 Tap (M12X1.75) | |
