Inlet and Exhaust Valves - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 9U-6195     | 气门弹簧压缩器     | 1     |
268-1969 | 适配器     | 1     | |
276-1221 | 盖     | 1     |
开始:
- 拆下缸盖。 有关的正确程序,请参阅拆解与组装, "缸盖 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁缸盖底部配合面。 在拆卸气门弹簧之前,检查气门低于缸盖表面的深度。 请参阅技术规格, "缸盖气门",以了解正确的尺寸。
- 在气门头上作出临时的识别标记,以便确定正确的位置。
注: 进气门盖中央有一个凹槽。
- 使用适当的起吊设备放好缸盖,使气门弹簧朝上。 缸盖的重量约为 65 kg (143 lb)。
注: 确保将缸盖保存在一个清洁、柔软的表面上,以防损坏加工表面。
- 将工具 (A) 在缸盖上安装到位,以压缩相应的气门弹簧 (3) 。
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
Show/hide table
图 1 | g01978994 |
- 向工具 (A) 施加充足的压力,以便卸下气门保持器 (1) 。
注: 压缩弹簧时,不要使气门弹簧座 (2) 接触气门杆密封圈 (4) 。
Show/hide table
注意 |
---|
确保在四角均匀地压缩气门弹簧,否则可能会导致气门杆损坏。 |
- 缓慢地释放工具 (A) 上的压力。
- 在气门弹簧 (3) 上作一个临时识别标记,以便识别正确的位置。
Show/hide table
图 2 | g01978995 |
- 拆卸气门弹簧座 (2) 。 拆下气门弹簧 (3) 。
- 对其余气门重复步骤 4 至步骤 8。
- 拆下工具 (A) 。
- 卸下气门杆密封圈 (4) 。
- 使用适当的起吊设备翻转缸盖。
- 在气门 (5) 上作一个临时识别标记。 从缸盖上拆下气门 (5) 。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 9U-6195     | 气门弹簧压缩器     | 1     |
268-1969 | 适配器     | 1     | |
276-1221 | 盖     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 气门硬表面上有进行抛光处理。 气门上不可使用磨剂。 磨剂将会损坏气门的硬表面抛光。
- 清洁缸盖组件的所有部件。 确保缸盖的所有开口、冷却液通道和润滑通道中无碎屑。 按照第 1.a 到 1.e 步检查缸盖组件的部件。 更换任何损坏或磨损的部件。
- 检查缸盖有无磨损或损坏。 有关正确的步骤,请参阅系统操作、测试和调整, "缸盖检查"。
- 检查气门座有无磨损或损坏。 有关更多资料,请参阅技术规格, "缸盖气门"。
- 检查气门导管有无磨损或损坏。 有关更多资料,请参阅技术规格, "缸盖气门"和系统操作、测试和调整, "气门导管 - 检查"。
必须由经过正规培训的专业人员拆卸气门导管和气门座。 还需要使用专用机械设备。 有关更多信息,请咨询授权 Cat 代理商。
- 检查气门有无磨损或损坏。 有关更多资料,请参阅技术规格, "缸盖气门"。
- 检查气门弹簧有无磨损,以及长度是否正确。 有关更多资料,请参阅技术规格, "缸盖气门"。
- 使用清洁的发动机机油润滑气门 (5) 的杆。 将气门 (5) 安装在缸盖的相应位置中。 检查气门低于缸盖表面的深度。 有关更多资料,请参阅系统操作、测试和调整, "气门深度 - 检查"。
Show/hide table
图 3 | g01978995 |
- 使用适当的起吊设备翻转缸盖。 缸盖的重量约为 65 kg (143 lb)。
注: 确保所有气门仍保持在位。
- 将新气门杆密封圈 (4) 安装在各个气门导管上。
注: 安装气门杆密封圈 (4) 之前,气门导管外表面必须保持清洁、干燥。
- 将气门弹簧 (3) 安装到缸盖上。 将气门弹簧座 (2) 安置到气门弹簧 (3) 上。
- 将工具 (A) 安装在缸盖的相应位置中,以压缩气门弹簧 (3) 。
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
Show/hide table
图 4 | g01978994 |
- 向工具 (A) 施加足够的压力,以便安装气门保持器 (1) 。
注: 压缩弹簧时,不要使气门弹簧座 (2) 接触气门杆密封圈 (4) 。
Show/hide table
注意 |
---|
确保在四角均匀地压缩气门弹簧,否则可能会导致气门杆损坏。 |
- 小心地释放工具 (A) 上的压力。
Show/hide table
当松开气门弹簧压缩器的时候,气门弹簧卡座会从气门中弹出。 保证气门弹簧卡座正确安装在气门推杆上。 为了防止造成人员伤害,在安装气门时,应远离气门弹簧卡座前方和气门弹簧。 |
- 对其余气门重复步骤 5 至步骤 8。
- 将工具 (A) 从缸盖上拆下。
End By: 安装缸盖。 有关正确的步骤,请参阅 拆解与组装, "气缸盖 - 安装"。
Caterpillar Information System:
C7.1 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
844K Wheel Dozer Systems Pump Control Valve - Pressure, Flow compensator
C7.1 Industrial Engine Flexible Exhaust Pipe - Remove and Install
C7.1 Industrial Engine Exhaust Manifold - Remove and Install
C7.1 Industrial Engine DEF Injector and Mounting - Remove and Install
C7.1 Industrial Engine Wastegate Solenoid - Remove and Install
C7.1 Industrial Engine Turbocharger - Install - First Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Install - Second Stage Turbocharger
Procedure to Upgrade the 175-0183 Support Assembly on the 777D Off-Highway Truck{0629, 0632, 0679, 7253} Procedure to Upgrade the 175-0183 Support Assembly on the 777D Off-Highway Truck{0629, 0632, 0679, 7253}
C7.1 Industrial Engine Turbocharger - Install - First Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Install - Second Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Remove - First Stage Turbocharger
CB22B, CB24B, CB32B and CC24B Utility Compactors Water Spray System Filter - Clean
C7.1 Industrial Engine Engine Oil Filter Base - Remove and Install - Engine Oil Filter Base with Adapter
C7.1 Industrial Engine Engine Oil Filter Base - Remove and Install
C7.1 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
CB22B, CB24B, CB32B and CC24B Utility Compactors Capacities (Refill)
C7.1 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Industrial Engine Engine Oil Pump - Remove
C13 Tier 4 Final Engines Electronic Unit Injector - Adjust
CB22B, CB24B, CB32B and CC24B Utility Compactors Lubricant Viscosities - Fluids Recommendations
CB34B, CB34B XW, CB36B and CC34B Utility Compactors Lubricant Viscosities - Fluids Recommendations